Jump to content

File:Gin gang 021.jpg

Page contents not supported in other languages.
This is a file from the Wikimedia Commons
From Wikipedia, the free encyclopedia

Original file (3,648 × 2,736 pixels, file size: 1.6 MB, MIME type: image/jpeg)

Description
English: Showing semi-octagonal gin gang with slate roof at Beamish Museum, County Durham, England. The walls are sandstone or millstone grit blocks. The central spindle shaft of the horse mill can be seen in situ inside the gin gang. Beyond the gin gang is the type of portable steam engine which superseded the gin gangs of north-east England in the 1830s. This gin gang survived because its own mill was removed in the 1830s and the building was used for other purposes.
Gin gang

A gin gang is a structure built to enclose a horse mill, usually circular but sometimes square or octagonal, attached to a threshing barn. Most of the wood used here would have been seasoned oak originally, but much has been replaced during preservation, including apparently the main oak spindle-shaft of the mill, which appears to be unseasoned and cracked.

Roof construction

This renovated internal roof structure is based on a traditional space frame truss with its primary plane in line with the tie beam (or joist), and with members fixed between king post and rafters to support the semi-octagonal plan of the roof. There is one main transverse oak tie beam on which the king post of the main truss is based. The king post is in tension to prevent sagging of the horizontal tie beam, so neither the king post nor the tie beam are resting on the mill below. The roof construction is not structurally dependent on the horse mill, or connected with it.

The top of the mill's main vertical spindle shaft and the end of the main power shaft are pivoted at the centre of their own separate tie beam which is below and parallel with the main roof tie beam, and set in the gin gang's side walls at either end. The mill's tie beam has to be stabilised with two massive oak beams which run, either side of the power shaft, from tie beam to barn wall. A large and basic engine like this can create great stresses from the torque engendered.

Mill construction

This is based on a central, vertical, heavy, 10ft high, oak spindle shaft, with its base pivoting on an iron framework set in the middle of the gin gang floor. Its top end pivots under the mill's own tie beam (if it didn't, it would fall over) but the tie beam cannot rest on the pivot, or the mill would not turn. The spindle shaft supports around its top end the main, 6ft-diameter, horizontal gear wheel, with the teeth on the top surface. The main power shaft, a massive oak pole, is girthed at one end by a secondary gear wheel which lies on the main gear wheel, thus turning the main power shaft on its long axis. The main power shaft runs from the main gear wheel through a hole in the barn wall and in the barn it powers the threshing machine and other machines via further cogwheels and belts. Such a machine would create great torque stresses, and if it were ever to work again it would require re-engineering to ensure smooth and safe running, and beams which are seasoned and not cracked. NB: This mill was rescued from Berwick Hills Low Farm, Northumberland, and has had some repairs since then.

Horse power
This is a powerful horse mill for four horses; probably English ponies, as modern heavy horses were not yet fully bred in the 1830s. Each of the four heavy oak beams connecting the central spindle shaft to the four horse shafts runs from beside the spindle shaft to the under-surface of the main gear wheel, and crosses the other three in a grid pattern between the spindle shaft and gear wheel, thus supporting the gear wheel and creating a rigid structure at the same time. They project for many feet beyond the main gear wheel, and require wooden stretchers to stabilise them. From the ends of these beams hang the horse shafts. The bottom ends of these shafts are quite low, which may indicate the use of ponies rather than early heavy horses.
Date
Source Own work
Author Linda Spashett, Storye book
Permission
(Reusing this file)
I, the copyright holder of this work, hereby publish it under the following license:
w:en:Creative Commons
attribution
This file is licensed under the Creative Commons Attribution 3.0 Unported license.
You are free:
  • to share – to copy, distribute and transmit the work
  • to remix – to adapt the work
Under the following conditions:
  • attribution – You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.

Captions

Add a one-line explanation of what this file represents

Items portrayed in this file

depicts

17 April 2010

File history

Click on a date/time to view the file as it appeared at that time.

Date/TimeThumbnailDimensionsUserComment
current17:13, 19 April 2010Thumbnail for version as of 17:13, 19 April 20103,648 × 2,736 (1.6 MB)Storye book{{Information |Description={{en|1=Showing semi-octagonal gin gang with slate roof at Beamish Museum, County Durham, England. The walls are sandstone or millstone grit blocks. The central spindle shaft of the horse mill can be seen in situ inside the gin

The following 3 pages use this file:

Metadata