User:Rai282/Books/Modulation

Amplitude Modulation

Figure 1: An audio signal (top) may be carried by a carrier signal using AM or FM methods.

Amplitude modulation (AM) is a modulation technique used in electronic communication, most commonly for transmitting messages with a radio wave. In amplitude modulation, the amplitude (signal strength) of the wave is varied in proportion to that of the message signal, such as an audio signal. This technique contrasts with angle modulation, in which either the frequency of the carrier wave is varied, as in frequency modulation, or its phase, as in phase modulation.

AM was the earliest modulation method used for transmitting audio in radio broadcasting. It was developed during the first quarter of the 20th century beginning with Roberto Landell de Moura and Reginald Fessenden's radiotelephone experiments in 1900. This original form of AM is sometimes called double-sideband amplitude modulation (DSBAM), because the standard method produces sidebands on either side of the carrier frequency. Single-sideband modulation uses bandpass filters to eliminate one of the sidebands and possibly the carrier signal, which improves the ratio of message power to total transmission power, reduces power handling requirements of line repeaters, and permits better bandwidth utilization of the transmission medium.

AM remains in use in many forms of communication in addition to AM broadcasting: shortwave radio, amateur radio, two-way radios, VHF aircraft radio, citizens band radio, and in computer modems in the form of QAM.

Foundation

In electronics, telecommunications and mechanics, modulation means varying some aspect of a continuous wave carrier signal with an information-bearing modulation waveform, such as an audio signal which represents sound, or a video signal which represents images. In this sense, the carrier wave, which has a much higher frequency than the message signal, carries the information. At the receiving station, the message signal is extracted from the modulated carrier by demodulation.

In general form, a modulation process of a sinusoidal carrier wave may be described by the following equation:

$m(t)=A(t)\cdot \cos(\omega t+\phi (t))\,$.

A(t) represents the time-varying amplitude of the sinusoidal carrier wave and the cosine-term is the carrier at its angular frequency $\omega$, and the instantaneous phase deviation $\phi (t)$. This description directly provides the two major groups of modulation, amplitude modulation and angle modulation. In angle modulation, the term A(t) is constant and the second term of the equation has a functional relationship to the modulating message signal. Angle modulation provides two methods of modulation, frequency modulation and phase modulation.

In amplitude modulation, the angle term is held constant and the first term, A(t), of the equation has a functional relationship to the modulating message signal.

The modulating message signal may be analog in nature, or it may be a digital signal, in which case the technique is generally called amplitude-shift keying.

For example, in AM radio communication, a continuous wave radio-frequency signal has its amplitude modulated by an audio waveform before transmission. The message signal determines the envelope of the transmitted waveform. In the frequency domain, amplitude modulation produces a signal with power concentrated at the carrier frequency and two adjacent sidebands. Each sideband is equal in bandwidth to that of the modulating signal, and is a mirror image of the other. Standard AM is thus sometimes called "double-sideband amplitude modulation" (DSBAM).

A disadvantage of all amplitude modulation techniques, not only standard AM, is that the receiver amplifies and detects noise and electromagnetic interference in equal proportion to the signal. Increasing the received signal-to-noise ratio, say, by a factor of 10 (a 10 decibel improvement), thus would require increasing the transmitter power by a factor of 10. This is in contrast to frequency modulation (FM) and digital radio where the effect of such noise following demodulation is strongly reduced so long as the received signal is well above the threshold for reception. For this reason AM broadcast is not favored for music and high fidelity broadcasting, but rather for voice communications and broadcasts (sports, news, talk radio etc.).

AM is also inefficient in power usage; at least two-thirds of the power is concentrated in the carrier signal. The carrier signal contains none of the original information being transmitted (voice, video, data, etc.). However its presence provides a simple means of demodulation using envelope detection, providing a frequency and phase reference to extract the modulation from the sidebands. In some modulation systems based on AM, a lower transmitter power is required through partial or total elimination of the carrier component, however receivers for these signals are more complex because they must provide a precise carrier frequency reference signal (usually as shifted to the intermediate frequency) from a greatly reduced "pilot" carrier (in reduced-carrier transmission or DSB-RC) to use in the demodulation process. Even with the carrier eliminated in double-sideband suppressed-carrier transmission, carrier regeneration is possible using a Costas phase-locked loop. This does not work for single-sideband suppressed-carrier transmission (SSB-SC), leading to the characteristic "Donald Duck" sound from such receivers when slightly detuned. Single-sideband AM is nevertheless used widely in amateur radio and other voice communications because it has power and bandwidth efficiency (cutting the RF bandwidth in half compared to standard AM). On the other hand, in medium wave and short wave broadcasting, standard AM with the full carrier allows for reception using inexpensive receivers. The broadcaster absorbs the extra power cost to greatly increase potential audience.

Shift keying

A simple form of digital amplitude modulation which can be used for transmitting binary data is on–off keying, the simplest form of amplitude-shift keying, in which ones and zeros are represented by the presence or absence of a carrier. On–off keying is likewise used by radio amateurs to transmit Morse code where it is known as continuous wave (CW) operation, even though the transmission is not strictly "continuous". A more complex form of AM, quadrature amplitude modulation is now more commonly used with digital data, while making more efficient use of the available bandwidth.

Analog telephony

A simple form of amplitude modulation is the transmission of speech signals from a traditional analog telephone set using a common battery local loop. The direct current provided by the central office battery is a carrier with a frequency of 0 Hz. It is modulated by a microphone (transmitter) in the telephone set according to the acoustic signal from the speaker. The result is a varying amplitude direct current, whose AC-component is the speech signal extracted at the central office for transmission to another subscriber.

Amplitude reference

An additional function provided by the carrier in standard AM, but which is lost in either single or double-sideband suppressed-carrier transmission, is that it provides an amplitude reference. In the receiver, the automatic gain control (AGC) responds to the carrier so that the reproduced audio level stays in a fixed proportion to the original modulation. On the other hand, with suppressed-carrier transmissions there is no transmitted power during pauses in the modulation, so the AGC must respond to peaks of the transmitted power during peaks in the modulation. This typically involves a so-called fast attack, slow decay circuit which holds the AGC level for a second or more following such peaks, in between syllables or short pauses in the program. This is very acceptable for communications radios, where compression of the audio aids intelligibility. However it is absolutely undesired for music or normal broadcast programming, where a faithful reproduction of the original program, including its varying modulation levels, is expected.

ITU type designations

In 1982, the International Telecommunication Union (ITU) designated the types of amplitude modulation:

Designation	Description
A3E	double-sideband a full-carrier – the basic amplitude modulation scheme
R3E	single-sideband reduced-carrier
H3E	single-sideband full-carrier
J3E	single-sideband suppressed-carrier
B8E	independent-sideband emission
C3F	vestigial-sideband
Lincompex	linked compressor and expander (a submode of any of the above ITU Emission Modes)

History

One of the crude pre-vacuum tube AM transmitters, a Telefunken arc transmitter from 1906. The carrier wave is generated by 6 electric arcs in the vertical tubes, connected to a tuned circuit. Modulation is done by the large carbon microphone (cone shape) in the antenna lead.

One of the first vacuum tube AM radio transmitters, built by Meissner in 1913 with an early triode tube by Robert von Lieben. He used it in a historic 36 km (24 mi) voice transmission from Berlin to Nauen, Germany. Compare its small size with above transmitter.

Amplitude modulation was used in experiments of multiplex telegraph and telephone transmission in the late 1800s. However, the practical development of this technology is identified with the period between 1900 and 1920 of radiotelephone transmission, that is, the effort to send audio signals by radio waves. The first radio transmitters, called spark gap transmitters, transmitted information by wireless telegraphy, using pulses of the carrier wave to spell out text messages in Morse code. They could not transmit audio because the carrier consisted of strings of damped waves, pulses of radio waves that declined to zero, and sounded like a buzz in receivers. In effect they were already amplitude modulated.

Continuous waves

The first AM transmission was made by Canadian-born American researcher Reginald Fessenden on 23 December 1900 using a spark gap transmitter with a specially designed high frequency 10 kHz interrupter, over a distance of one mile (1.6 km) at Cobb Island, Maryland, US. His first transmitted words were, "Hello. One, two, three, four. Is it snowing where you are, Mr. Thiessen?". The words were barely intelligible above the background buzz of the spark.

Fessenden was a significant figure in the development of AM radio. He was one of the first researchers to realize, from experiments like the above, that the existing technology for producing radio waves, the spark transmitter, was not usable for amplitude modulation, and that a new kind of transmitter, one that produced sinusoidal continuous waves, was needed. This was a radical idea at the time, because experts believed the impulsive spark was necessary to produce radio frequency waves, and Fessenden was ridiculed. He invented and helped develop one of the first continuous wave transmitters – the Alexanderson alternator, with which he made what is considered the first AM public entertainment broadcast on Christmas Eve, 1906. He also discovered the principle on which AM is based, heterodyning, and invented one of the first detectors able to rectify and receive AM, the electrolytic detector or "liquid baretter", in 1902. Other radio detectors invented for wireless telegraphy, such as the Fleming valve (1904) and the crystal detector (1906) also proved able to rectify AM signals, so the technological hurdle was generating AM waves; receiving them was not a problem.

Early technologies

Early experiments in AM radio transmission, conducted by Fessenden, Valdemar Poulsen, Ernst Ruhmer, Quirino Majorana, Charles Herrold, and Lee de Forest, were hampered by the lack of a technology for amplification. The first practical continuous wave AM transmitters were based on either the huge, expensive Alexanderson alternator, developed 1906–1910, or versions of the Poulsen arc transmitter (arc converter), invented in 1903. The modifications necessary to transmit AM were clumsy and resulted in very low quality audio. Modulation was usually accomplished by a carbon microphone inserted directly in the antenna or ground wire; its varying resistance varied the current to the antenna. The limited power handling ability of the microphone severely limited the power of the first radiotelephones; many of the microphones were water-cooled.

Vacuum tubes

The 1912 discovery of the amplifying ability of the Audion tube, invented in 1906 by Lee de Forest, solved these problems. The vacuum tube feedback oscillator, invented in 1912 by Edwin Armstrong and Alexander Meissner, was a cheap source of continuous waves and could be easily modulated to make an AM transmitter. Modulation did not have to be done at the output but could be applied to the signal before the final amplifier tube, so the microphone or other audio source didn't have to modulate a high-power radio signal. Wartime research greatly advanced the art of AM modulation, and after the war the availability of cheap tubes sparked a great increase in the number of radio stations experimenting with AM transmission of news or music. The vacuum tube was responsible for the rise of AM broadcasting around 1920, the first electronic mass communication medium. Amplitude modulation was virtually the only type used for radio broadcasting until FM broadcasting began after World War II.

At the same time as AM radio began, telephone companies such as AT&T were developing the other large application for AM: sending multiple telephone calls through a single wire by modulating them on separate carrier frequencies, called frequency division multiplexing.

Single-sideband

In 1915, John Renshaw Carson formulated the first mathematical description of amplitude modulation, showing that a signal and carrier frequency combined in a nonlinear device creates a sideband on both sides of the carrier frequency. Passing the modulated signal through another nonlinear device can extract the original baseband signal. His analysis also showed that only one sideband was necessary to transmit the audio signal, and Carson patented single-sideband modulation (SSB) on 1 December 1915. This advanced variant of amplitude modulation was adopted by AT&T for longwave transatlantic telephone service beginning 7 January 1927. After WW-II, it was developed for military aircraft communication.

Analysis

Illustration of amplitude modulation

The carrier wave (sine wave) of frequency f_c and amplitude A is expressed by

$c(t)=A\sin(2\pi f_{c}t)\,$.

The message signal, such as an audio signal that is used for modulating the carrier, is m(t), and has a frequency f_m, much lower than f_c:

$m(t)=M\cos \left(2\pi f_{m}t+\phi \right)=Am\cos \left(2\pi f_{m}t+\phi \right)\,$,

where m is the amplitude sensitivity, M is the amplitude of modulation. If m < 1, (1 + m(t)/A) is always positive for undermodulation. If m > 1 then overmodulation occurs and reconstruction of message signal from the transmitted signal would lead in loss of original signal. Amplitude modulation results when the carrier c(t) is multiplied by the positive quantity (1 + m(t)/A):

${\begin{aligned}y(t)&=\left[1+{\frac {m(t)}{A}}\right]c(t)\\&=\left[1+m\cos \left(2\pi f_{m}t+\phi \right)\right]A\sin \left(2\pi f_{c}t\right)\end{aligned}}$

In this simple case m is identical to the modulation index, discussed below. With m = 0.5 the amplitude modulated signal y(t) thus corresponds to the top graph (labelled "50% Modulation") in figure 4.

Using prosthaphaeresis identities, y(t) can be shown to be the sum of three sine waves:

$y(t)=A\sin(2\pi f_{c}t)+{\frac {1}{2}}Am\left[\sin \left(2\pi \left[f_{c}+f_{m}\right]t+\phi \right)+\sin \left(2\pi \left[f_{c}-f_{m}\right]t-\phi \right)\right].\,$

Therefore, the modulated signal has three components: the carrier wave c(t) which is unchanged in frequency, and two sidebands with frequencies slightly above and below the carrier frequency f_c.

Spectrum

Figure 2: Double-sided spectra of baseband and AM signals.

A useful modulation signal m(t) is usually more complex than a single sine wave, as treated above. However, by the principle of Fourier decomposition, m(t) can be expressed as the sum of a set of sine waves of various frequencies, amplitudes, and phases. Carrying out the multiplication of 1 + m(t) with c(t) as above, the result consists of a sum of sine waves. Again, the carrier c(t) is present unchanged, but each frequency component of m at f_i has two sidebands at frequencies f_c + f_i and f_c – f_i. The collection of the former frequencies above the carrier frequency is known as the upper sideband, and those below constitute the lower sideband. The modulation m(t) may be considered to consist of an equal mix of positive and negative frequency components, as shown in the top of figure 2. One can view the sidebands as that modulation m(t) having simply been shifted in frequency by f_c as depicted at the bottom right of figure 2.

Figure 3: The spectrogram of an AM voice broadcast shows the two sidebands (green) on either side of the carrier (red) with time proceeding in the vertical direction.

The short-term spectrum of modulation, changing as it would for a human voice for instance, the frequency content (horizontal axis) may be plotted as a function of time (vertical axis), as in figure 3. It can again be seen that as the modulation frequency content varies, an upper sideband is generated according to those frequencies shifted above the carrier frequency, and the same content mirror-imaged in the lower sideband below the carrier frequency. At all times, the carrier itself remains constant, and of greater power than the total sideband power.

Power and spectrum efficiency

The RF bandwidth of an AM transmission (refer to figure 2, but only considering positive frequencies) is twice the bandwidth of the modulating (or "baseband") signal, since the upper and lower sidebands around the carrier frequency each have a bandwidth as wide as the highest modulating frequency. Although the bandwidth of an AM signal is narrower than one using frequency modulation (FM), it is twice as wide as single-sideband techniques; it thus may be viewed as spectrally inefficient. Within a frequency band, only half as many transmissions (or "channels") can thus be accommodated. For this reason analog television employs a variant of single-sideband (known as vestigial sideband, somewhat of a compromise in terms of bandwidth) in order to reduce the required channel spacing.

Another improvement over standard AM is obtained through reduction or suppression of the carrier component of the modulated spectrum. In figure 2 this is the spike in between the sidebands; even with full (100%) sine wave modulation, the power in the carrier component is twice that in the sidebands, yet it carries no unique information. Thus there is a great advantage in efficiency in reducing or totally suppressing the carrier, either in conjunction with elimination of one sideband (single-sideband suppressed-carrier transmission) or with both sidebands remaining (double sideband suppressed carrier). While these suppressed carrier transmissions are efficient in terms of transmitter power, they require more sophisticated receivers employing synchronous detection and regeneration of the carrier frequency. For that reason, standard AM continues to be widely used, especially in broadcast transmission, to allow for the use of inexpensive receivers using envelope detection. Even (analog) television, with a (largely) suppressed lower sideband, includes sufficient carrier power for use of envelope detection. But for communications systems where both transmitters and receivers can be optimized, suppression of both one sideband and the carrier represent a net advantage and are frequently employed.

A technique used widely in broadcast AM transmitters is an application of the Hapburg carrier, first proposed in the 1930s but impractical with the technology then available. During periods of low modulation the carrier power would be reduced and would return to full power during periods of high modulation levels. This has the effect of reducing the overall power demand of the transmitter and is most effective on speech type programmes. Various trade names are used for its implementation by the transmitter manufacturers from the late 80's onwards.

Modulation index

The AM modulation index is a measure based on the ratio of the modulation excursions of the RF signal to the level of the unmodulated carrier. It is thus defined as:

$m={\frac {\mathrm {peak\ value\ of\ } m(t)}{A}}={\frac {M}{A}}$

where $M\,$ and $A\,$ are the modulation amplitude and carrier amplitude, respectively; the modulation amplitude is the peak (positive or negative) change in the RF amplitude from its unmodulated value. Modulation index is normally expressed as a percentage, and may be displayed on a meter connected to an AM transmitter.

So if $m=0.5$, carrier amplitude varies by 50% above (and below) its unmodulated level, as is shown in the first waveform, below. For $m=1.0$, it varies by 100% as shown in the illustration below it. With 100% modulation the wave amplitude sometimes reaches zero, and this represents full modulation using standard AM and is often a target (in order to obtain the highest possible signal-to-noise ratio) but mustn't be exceeded. Increasing the modulating signal beyond that point, known as overmodulation, causes a standard AM modulator (see below) to fail, as the negative excursions of the wave envelope cannot become less than zero, resulting in distortion ("clipping") of the received modulation. Transmitters typically incorporate a limiter circuit to avoid overmodulation, and/or a compressor circuit (especially for voice communications) in order to still approach 100% modulation for maximum intelligibility above the noise. Such circuits are sometimes referred to as a vogad.

However it is possible to talk about a modulation index exceeding 100%, without introducing distortion, in the case of double-sideband reduced-carrier transmission. In that case, negative excursions beyond zero entail a reversal of the carrier phase, as shown in the third waveform below. This cannot be produced using the efficient high-level (output stage) modulation techniques (see below) which are widely used especially in high power broadcast transmitters. Rather, a special modulator produces such a waveform at a low level followed by a linear amplifier. What's more, a standard AM receiver using an envelope detector is incapable of properly demodulating such a signal. Rather, synchronous detection is required. Thus double-sideband transmission is generally not referred to as "AM" even though it generates an identical RF waveform as standard AM as long as the modulation index is below 100%. Such systems more often attempt a radical reduction of the carrier level compared to the sidebands (where the useful information is present) to the point of double-sideband suppressed-carrier transmission where the carrier is (ideally) reduced to zero. In all such cases the term "modulation index" loses its value as it refers to the ratio of the modulation amplitude to a rather small (or zero) remaining carrier amplitude.

Figure 4: Modulation depth. In the diagram, the unmodulated carrier has an amplitude of 1.

Modulation methods

Anode (plate) modulation. A tetrode's plate and screen grid voltage is modulated via an audio transformer. The resistor R1 sets the grid bias; both the input and output are tuned circuits with inductive coupling.

Modulation circuit designs may be classified as low- or high-level (depending on whether they modulate in a low-power domain—followed by amplification for transmission—or in the high-power domain of the transmitted signal).

Low-level generation

In modern radio systems, modulated signals are generated via digital signal processing (DSP). With DSP many types of AM are possible with software control (including DSB with carrier, SSB suppressed-carrier and independent sideband, or ISB). Calculated digital samples are converted to voltages with a digital-to-analog converter, typically at a frequency less than the desired RF-output frequency. The analog signal must then be shifted in frequency and linearly amplified to the desired frequency and power level (linear amplification must be used to prevent modulation distortion). This low-level method for AM is used in many Amateur Radio transceivers.

AM may also be generated at a low level, using analog methods described in the next section.

High-level generation

High-power AM transmitters (such as those used for AM broadcasting) are based on high-efficiency class-D and class-E power amplifier stages, modulated by varying the supply voltage.

Older designs (for broadcast and amateur radio) also generate AM by controlling the gain of the transmitter's final amplifier (generally class-C, for efficiency). The following types are for vacuum tube transmitters (but similar options are available with transistors):

Plate modulation

In plate modulation, the plate voltage of the RF amplifier is modulated with the audio signal. The audio power requirement is 50 percent of the RF-carrier power.

Heising (constant-current) modulation

RF amplifier plate voltage is fed through a choke (high-value inductor). The AM modulation tube plate is fed through the same inductor, so the modulator tube diverts current from the RF amplifier. The choke acts as a constant current source in the audio range. This system has a low power efficiency.

Control grid modulation

The operating bias and gain of the final RF amplifier can be controlled by varying the voltage of the control grid. This method requires little audio power, but care must be taken to reduce distortion.

Clamp tube (screen grid) modulation

The screen-grid bias may be controlled through a clamp tube, which reduces voltage according to the modulation signal. It is difficult to approach 100-percent modulation while maintaining low distortion with this system.

Doherty modulation

One tube provides the power under carrier conditions and another operates only for positive modulation peaks. Overall efficiency is good, and distortion is low.

Outphasing modulation

Two tubes are operated in parallel, but partially out of phase with each other. As they are differentially phase modulated their combined amplitude is greater or smaller. Efficiency is good and distortion low when properly adjusted.

Pulse-width modulation (PWM) or pulse-duration modulation (PDM)

A highly efficient high voltage power supply is applied to the tube plate. The output voltage of this supply is varied at an audio rate to follow the program. This system was pioneered by Hilmer Swanson and has a number of variations, all of which achieve high efficiency and sound quality.

Digital methods

The Harris Corporation obtained a patent for synthesizing a modulated high-power carrier wave from a set of digitally selected low-power amplifiers, running in phase at the same carrier frequency. The input signal is sampled by a conventional audio analog-to-digital converter (ADC), and fed to a digital exciter, which modulates overall transmitter output power by switching a series of low-power solid-state RF amplifiers on and off. The combined output drives the antenna system.

Demodulation methods

The simplest form of AM demodulator consists of a diode which is configured to act as envelope detector. Another type of demodulator, the product detector, can provide better-quality demodulation with additional circuit complexity.

See also

• AM stereo
• Shortwave radio
• Amplitude modulation signalling system (AMSS)
• Modulation sphere
• Types of radio emissions
• Airband
• DSB-SC

Bibliography

• Newkirk, David and Karlquist, Rick (2004). Mixers, modulators and demodulators. In D. G. Reed (ed.), The ARRL Handbook for Radio Communications (81st ed.), pp. 15.1–15.36. Newington: ARRL. ISBN 0-87259-196-4.

External links

• Amplitude Modulation by Jakub Serych, Wolfram Demonstrations Project.
• Amplitude Modulation, by S Sastry.
• Amplitude Modulation, an introduction by Federation of American Scientists.
• Amplitude Modulation tutorial including related topics of modulators, demodulators, etc...
• Analog Modulation online interactive demonstration using Python in Google Colab Platform, by C Foh.

Frequency Modulation

For the application of frequency modulation to radio broadcasting, see FM broadcasting.

"NFM" redirects here. For other uses, see NFM (disambiguation).

A signal may be carried by an AM or FM radio wave.

FM has better noise (RFI) rejection than AM, as shown in this dramatic New York publicity demonstration by General Electric in 1940. The radio has both AM and FM receivers. With a million-volt electric arc as a source of interference behind it, the AM receiver produced only a roar of static, while the FM receiver clearly reproduced a music program from Armstrong's experimental FM transmitter W2XMN in New Jersey.

Frequency modulation (FM) is the encoding of information in a carrier wave by varying the instantaneous frequency of the wave. The technology is used in telecommunications, radio broadcasting, signal processing, and computing.

In analog frequency modulation, such as radio broadcasting, of an audio signal representing voice or music, the instantaneous frequency deviation, i.e. the difference between the frequency of the carrier and its center frequency, has a functional relation to the modulating signal amplitude.

Digital data can be encoded and transmitted with a type of frequency modulation known as frequency-shift keying (FSK), in which the instantaneous frequency of the carrier is shifted among a set of frequencies. The frequencies may represent digits, such as '0' and '1'. FSK is widely used in computer modems, such as fax modems, telephone caller ID systems, garage door openers, and other low-frequency transmissions. Radioteletype also uses FSK.

Frequency modulation is widely used for FM radio broadcasting. It is also used in telemetry, radar, seismic prospecting, and monitoring newborns for seizures via EEG, two-way radio systems, sound synthesis, magnetic tape-recording systems and some video-transmission systems. In radio transmission, an advantage of frequency modulation is that it has a larger signal-to-noise ratio and therefore rejects radio frequency interference better than an equal power amplitude modulation (AM) signal. For this reason, most music is broadcast over FM radio.

However, under severe enough multipath conditions it performs much more poorly than AM, with distinct high frequency noise artifacts that are audible with lower volumes and less complex tones. With high enough volume and carrier deviation audio distortion starts to occur that otherwise wouldn't be present without multipath or with an AM signal.

Frequency modulation and phase modulation are the two complementary principal methods of angle modulation; phase modulation is often used as an intermediate step to achieve frequency modulation. These methods contrast with amplitude modulation, in which the amplitude of the carrier wave varies, while the frequency and phase remain constant.

Theory

If the information to be transmitted (i.e., the baseband signal) is $x_{m}(t)$ and the sinusoidal carrier is $x_{c}(t)=A_{c}\cos(2\pi f_{c}t)\,$, where f_c is the carrier's base frequency, and A_c is the carrier's amplitude, the modulator combines the carrier with the baseband data signal to get the transmitted signal:

${\begin{aligned}y(t)&=A_{c}\cos \left(2\pi \int _{0}^{t}f(\tau )d\tau \right)\\&=A_{c}\cos \left(2\pi \int _{0}^{t}\left[f_{c}+f_{\Delta }x_{m}(\tau )\right]d\tau \right)\\&=A_{c}\cos \left(2\pi f_{c}t+2\pi f_{\Delta }\int _{0}^{t}x_{m}(\tau )d\tau \right)\\\end{aligned}}$

where $f_{\Delta }=K_{f}A_{m}$, $K_{f}$ being the sensitivity of the frequency modulator and $A_{m}$ being the amplitude of the modulating signal or baseband signal.

In this equation, $f(\tau )\,$ is the instantaneous frequency of the oscillator and $f_{\Delta }\,$ is the frequency deviation, which represents the maximum shift away from f_c in one direction, assuming x_m(t) is limited to the range ±1.

It is important to realize that this process of integrating the instantaneous frequency to create an instantaneous phase is quite different from what the term "frequency modulation" naively implies, namely directly adding the modulating signal to the carrier frequency

${\begin{aligned}y(t)&=A_{c}\cos \left(2\pi \left[f_{c}+f_{\Delta }x_{m}(t)\right]t\right)\end{aligned}}$

which would result in a modulated signal that has spurious local minima and maxima that do not correspond to those of the carrier.

While most of the energy of the signal is contained within f_c ± f_Δ, it can be shown by Fourier analysis that a wider range of frequencies is required to precisely represent an FM signal. The frequency spectrum of an actual FM signal has components extending infinitely, although their amplitude decreases and higher-order components are often neglected in practical design problems.

Sinusoidal baseband signal

Mathematically, a baseband modulating signal may be approximated by a sinusoidal continuous wave signal with a frequency f_m. This method is also named as single-tone modulation. The integral of such a signal is:

$\int _{0}^{t}x_{m}(\tau )d\tau ={\frac {\sin \left(2\pi f_{m}t\right)}{2\pi f_{m}}}\,$

In this case, the expression for y(t) above simplifies to:

$y(t)=A_{c}\cos \left(2\pi f_{c}t+{\frac {f_{\Delta }}{f_{m}}}\sin \left(2\pi f_{m}t\right)\right)\,$

where the amplitude $A_{m}\,$ of the modulating sinusoid is represented in the peak deviation $f_{\Delta }=K_{f}A_{m}$ (see frequency deviation).

The harmonic distribution of a sine wave carrier modulated by such a sinusoidal signal can be represented with Bessel functions; this provides the basis for a mathematical understanding of frequency modulation in the frequency domain.

Modulation index

As in other modulation systems, the modulation index indicates by how much the modulated variable varies around its unmodulated level. It relates to variations in the carrier frequency:

$h={\frac {\Delta {}f}{f_{m}}}={\frac {f_{\Delta }\left|x_{m}(t)\right|}{f_{m}}}$

where $f_{m}\,$ is the highest frequency component present in the modulating signal x_m(t), and $\Delta {}f\,$ is the peak frequency-deviation – i.e. the maximum deviation of the instantaneous frequency from the carrier frequency. For a sine wave modulation, the modulation index is seen to be the ratio of the peak frequency deviation of the carrier wave to the frequency of the modulating sine wave.

If $h\ll 1$, the modulation is called narrowband FM (NFM), and its bandwidth is approximately $2f_{m}\,$. Sometimes modulation index $h<0.3$ is considered NFM and other modulation indices are considered wideband FM (WFM or FM).

For digital modulation systems, for example, binary frequency shift keying (BFSK), where a binary signal modulates the carrier, the modulation index is given by:

$h={\frac {\Delta {}f}{f_{m}}}={\frac {\Delta {}f}{\frac {1}{2T_{s}}}}=2\Delta {}fT_{s}\$

where $T_{s}\,$ is the symbol period, and $f_{m}={\frac {1}{2T_{s}}}\,$ is used as the highest frequency of the modulating binary waveform by convention, even though it would be more accurate to say it is the highest fundamental of the modulating binary waveform. In the case of digital modulation, the carrier $f_{c}\,$ is never transmitted. Rather, one of two frequencies is transmitted, either $f_{c}+\Delta f$ or $f_{c}-\Delta f$, depending on the binary state 0 or 1 of the modulation signal.

If $h\gg 1$, the modulation is called wideband FM and its bandwidth is approximately $2f_{\Delta }\,$. While wideband FM uses more bandwidth, it can improve the signal-to-noise ratio significantly; for example, doubling the value of $\Delta {}f\,$, while keeping $f_{m}$ constant, results in an eight-fold improvement in the signal-to-noise ratio. (Compare this with chirp spread spectrum, which uses extremely wide frequency deviations to achieve processing gains comparable to traditional, better-known spread-spectrum modes).

With a tone-modulated FM wave, if the modulation frequency is held constant and the modulation index is increased, the (non-negligible) bandwidth of the FM signal increases but the spacing between spectra remains the same; some spectral components decrease in strength as others increase. If the frequency deviation is held constant and the modulation frequency increased, the spacing between spectra increases.

Frequency modulation can be classified as narrowband if the change in the carrier frequency is about the same as the signal frequency, or as wideband if the change in the carrier frequency is much higher (modulation index > 1) than the signal frequency. For example, narrowband FM (NFM) is used for two-way radio systems such as Family Radio Service, in which the carrier is allowed to deviate only 2.5 kHz above and below the center frequency with speech signals of no more than 3.5 kHz bandwidth. Wideband FM is used for FM broadcasting, in which music and speech are transmitted with up to 75 kHz deviation from the center frequency and carry audio with up to a 20 kHz bandwidth and subcarriers up to 92 kHz.

Bessel functions

Frequency spectrum and waterfall plot of a 146.52 MHz carrier, frequency modulated by a 1,000 Hz sinusoid. The modulation index has been adjusted to around 2.4, so the carrier frequency has small amplitude. Several strong sidebands are apparent; in principle an infinite number are produced in FM but the higher-order sidebands are of negligible magnitude.

For the case of a carrier modulated by a single sine wave, the resulting frequency spectrum can be calculated using Bessel functions of the first kind, as a function of the sideband number and the modulation index. The carrier and sideband amplitudes are illustrated for different modulation indices of FM signals. For particular values of the modulation index, the carrier amplitude becomes zero and all the signal power is in the sidebands.

Since the sidebands are on both sides of the carrier, their count is doubled, and then multiplied by the modulating frequency to find the bandwidth. For example, 3 kHz deviation modulated by a 2.2 kHz audio tone produces a modulation index of 1.36. Suppose that we limit ourselves to only those sidebands that have a relative amplitude of at least 0.01. Then, examining the chart shows this modulation index will produce three sidebands. These three sidebands, when doubled, gives us (6 × 2.2 kHz) or a 13.2 kHz required bandwidth.

Modulation index	Sideband amplitude
	Carrier	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0.00	1.00
0.25	0.98	0.12
0.5	0.94	0.24	0.03
1.0	0.77	0.44	0.11	0.02
1.5	0.51	0.56	0.23	0.06	0.01
2.0	0.22	0.58	0.35	0.13	0.03
2.40483	0.00	0.52	0.43	0.20	0.06	0.02
2.5	−0.05	0.50	0.45	0.22	0.07	0.02	0.01
3.0	−0.26	0.34	0.49	0.31	0.13	0.04	0.01
4.0	−0.40	−0.07	0.36	0.43	0.28	0.13	0.05	0.02
5.0	−0.18	−0.33	0.05	0.36	0.39	0.26	0.13	0.05	0.02
5.52008	0.00	−0.34	−0.13	0.25	0.40	0.32	0.19	0.09	0.03	0.01
6.0	0.15	−0.28	−0.24	0.11	0.36	0.36	0.25	0.13	0.06	0.02
7.0	0.30	0.00	−0.30	−0.17	0.16	0.35	0.34	0.23	0.13	0.06	0.02
8.0	0.17	0.23	−0.11	−0.29	−0.10	0.19	0.34	0.32	0.22	0.13	0.06	0.03
8.65373	0.00	0.27	0.06	−0.24	−0.23	0.03	0.26	0.34	0.28	0.18	0.10	0.05	0.02
9.0	−0.09	0.25	0.14	−0.18	−0.27	−0.06	0.20	0.33	0.31	0.21	0.12	0.06	0.03	0.01
10.0	−0.25	0.04	0.25	0.06	−0.22	−0.23	−0.01	0.22	0.32	0.29	0.21	0.12	0.06	0.03	0.01
12.0	0.05	−0.22	−0.08	0.20	0.18	−0.07	−0.24	−0.17	0.05	0.23	0.30	0.27	0.20	0.12	0.07	0.03	0.01

Carson's rule

Main article: Carson bandwidth rule

A rule of thumb, Carson's rule states that nearly all (≈98 percent) of the power of a frequency-modulated signal lies within a bandwidth $B_{T}\,$ of:

$B_{T}=2\left(\Delta f+f_{m}\right)=2f_{m}(\beta +1)$

where $\Delta f\,$, as defined above, is the peak deviation of the instantaneous frequency $f(t)\,$ from the center carrier frequency $f_{c}$, $\beta$ is the Modulation index which is the ratio of frequency deviation to highest frequency in the modulating signal and $f_{m}\,$is the highest frequency in the modulating signal. Condition for application of Carson's rule is only sinusoidal signals. For non-sinusoidal signals:

$B_{T}=2(\Delta f+W)=2W(D+1)$

where W is the highest frequency in the modulating signal but non-sinusoidal in nature and D is the Deviation ratio which the ratio of frequency deviation to highest frequency of modulating non-sinusoidal signal.

Noise reduction

FM provides improved signal-to-noise ratio (SNR), as compared for example with AM. Compared with an optimum AM scheme, FM typically has poorer SNR below a certain signal level called the noise threshold, but above a higher level – the full improvement or full quieting threshold – the SNR is much improved over AM. The improvement depends on modulation level and deviation. For typical voice communications channels, improvements are typically 5–15 dB. FM broadcasting using wider deviation can achieve even greater improvements. Additional techniques, such as pre-emphasis of higher audio frequencies with corresponding de-emphasis in the receiver, are generally used to improve overall SNR in FM circuits. Since FM signals have constant amplitude, FM receivers normally have limiters that remove AM noise, further improving SNR.

Implementation

Modulation

FM signals can be generated using either direct or indirect frequency modulation:

• Direct FM modulation can be achieved by directly feeding the message into the input of a voltage-controlled oscillator.
• For indirect FM modulation, the message signal is integrated to generate a phase-modulated signal. This is used to modulate a crystal-controlled oscillator, and the result is passed through a frequency multiplier to produce an FM signal. In this modulation, narrowband FM is generated leading to wideband FM later and hence the modulation is known as indirect FM modulation.

Demodulation

See also: Detector (radio) § Frequency and phase modulation detectors

FM modulation

Many FM detector circuits exist. A common method for recovering the information signal is through a Foster–Seeley discriminator or ratio detector. A phase-locked loop can be used as an FM demodulator. Slope detection demodulates an FM signal by using a tuned circuit which has its resonant frequency slightly offset from the carrier. As the frequency rises and falls the tuned circuit provides a changing amplitude of response, converting FM to AM. AM receivers may detect some FM transmissions by this means, although it does not provide an efficient means of detection for FM broadcasts. In Software-Defined Radio implementations the demodulation may be carried out by using the Hilbert transform (implemented as a filter) to recover the instantaneous phase, and thereafter differentiating this phase (using another filter) to recover the instantaneous frequency. Alternatively, a complex mixer followed by a bandpass filter may be used to translate the signal to baseband, and then proceeding as before.

Applications

Doppler effect

When an echolocating bat approaches a target, its outgoing sounds return as echoes, which are Doppler-shifted upward in frequency. In certain species of bats, which produce constant frequency (CF) echolocation calls, the bats compensate for the Doppler shift by lowering their call frequency as they approach a target. This keeps the returning echo in the same frequency range of the normal echolocation call. This dynamic frequency modulation is called the Doppler Shift Compensation (DSC), and was discovered by Hans Schnitzler in 1968.

Magnetic tape storage

FM is also used at intermediate frequencies by analog VCR systems (including VHS) to record the luminance (black and white) portions of the video signal. Commonly, the chrominance component is recorded as a conventional AM signal, using the higher-frequency FM signal as bias. FM is the only feasible method of recording the luminance ("black-and-white") component of video to (and retrieving video from) magnetic tape without distortion; video signals have a large range of frequency components – from a few hertz to several megahertz, too wide for equalizers to work with due to electronic noise below −60 dB. FM also keeps the tape at saturation level, acting as a form of noise reduction; a limiter can mask variations in playback output, and the FM capture effect removes print-through and pre-echo. A continuous pilot-tone, if added to the signal – as was done on V2000 and many Hi-band formats – can keep mechanical jitter under control and assist timebase correction.

These FM systems are unusual, in that they have a ratio of carrier to maximum modulation frequency of less than two; contrast this with FM audio broadcasting, where the ratio is around 10,000. Consider, for example, a 6-MHz carrier modulated at a 3.5-MHz rate; by Bessel analysis, the first sidebands are on 9.5 and 2.5 MHz and the second sidebands are on 13 MHz and −1 MHz. The result is a reversed-phase sideband on +1 MHz; on demodulation, this results in unwanted output at 6 – 1 = 5 MHz. The system must be designed so that this unwanted output is reduced to an acceptable level.

Sound

FM is also used at audio frequencies to synthesize sound. This technique, known as FM synthesis, was popularized by early digital synthesizers and became a standard feature in several generations of personal computer sound cards.

Radio

Main article: FM broadcasting

An American FM radio transmitter in Buffalo, NY at WEDG

Edwin Howard Armstrong (1890–1954) was an American electrical engineer who invented wideband frequency modulation (FM) radio. He patented the regenerative circuit in 1914, the superheterodyne receiver in 1918 and the super-regenerative circuit in 1922. Armstrong presented his paper, "A Method of Reducing Disturbances in Radio Signaling by a System of Frequency Modulation", (which first described FM radio) before the New York section of the Institute of Radio Engineers on November 6, 1935. The paper was published in 1936.

As the name implies, wideband FM (WFM) requires a wider signal bandwidth than amplitude modulation by an equivalent modulating signal; this also makes the signal more robust against noise and interference. Frequency modulation is also more robust against signal-amplitude-fading phenomena. As a result, FM was chosen as the modulation standard for high frequency, high fidelity radio transmission, hence the term "FM radio" (although for many years the BBC called it "VHF radio" because commercial FM broadcasting uses part of the VHF band – the FM broadcast band). FM receivers employ a special detector for FM signals and exhibit a phenomenon known as the capture effect, in which the tuner "captures" the stronger of two stations on the same frequency while rejecting the other (compare this with a similar situation on an AM receiver, where both stations can be heard simultaneously). Frequency drift or a lack of selectivity may cause one station to be overtaken by another on an adjacent channel. Frequency drift was a problem in early (or inexpensive) receivers; inadequate selectivity may affect any tuner.

A wideband FM signal can also be used to carry a stereo signal; this is done with multiplexing and demultiplexing before and after the FM process. The FM modulation and demodulation process is identical in stereo and monaural processes.

FM is commonly used at VHF radio frequencies for high-fidelity broadcasts of music and speech. In broadcast services, where audio fidelity is important, wideband FM is generally used. Analog TV sound is also broadcast using FM. Narrowband FM is used for voice communications in commercial and amateur radio settings. In two-way radio, narrowband FM (NBFM) is used to conserve bandwidth for land mobile, marine mobile and other radio services.

A high-efficiency radio-frequency switching amplifier can be used to transmit FM signals (and other constant-amplitude signals). For a given signal strength (measured at the receiver antenna), switching amplifiers use less battery power and typically cost less than a linear amplifier. This gives FM another advantage over other modulation methods requiring linear amplifiers, such as AM and QAM.

There are reports that on October 5, 1924, Professor Mikhail A. Bonch-Bruevich, during a scientific and technical conversation in the Nizhny Novgorod Radio Laboratory, reported about his new method of telephony, based on a change in the period of oscillations. Demonstration of frequency modulation was carried out on the laboratory model.

Hearing assistive technology

Frequency modulated systems are a widespread and commercially available assistive technology that make speech more understandable by improving the signal-to-noise ratio in the user's ear. They are also called auditory trainers, a term which refers to any sound amplification system not classified as a hearing aid. They intensify signal levels from the source by 15 to 20 decibels. FM systems are used by hearing-impaired people as well as children whose listening is affected by disorders such as auditory processing disorder or ADHD. For people with sensorineural hearing loss, FM systems result in better speech perception than hearing aids. They can be coupled with behind-the-ear hearing aids to allow the user to alternate the setting. FM systems are more convenient and cost-effective than alternatives such as cochlear implants, but many users use FM systems infrequently due to their conspicuousness and need for recharging.

See also

• Amplitude modulation
• Continuous-wave frequency-modulated radar
• Chirp
• FM broadcasting
• FM stereo
• FM-UWB (FM and Ultra Wideband)
• History of radio
• Modulation, for a list of other modulation techniques
• Phase modulation

Further reading

• Carlson, A. Bruce (2001). Communication Systems. Science/Engineering/Math (4th ed.). McGraw-Hill. ISBN 978-0-07-011127-1.
• Frost, Gary L. (2010). Early FM Radio: Incremental technology in twentieth-century America. Baltimore, MD: Johns Hopkins University Press. ISBN 978-0-8018-9440-4.
• Seymour, Ken (2005) [1996]. "Frequency Modulation". The Electronics Handbook (2nd ed.). CRC Press. pp. 1188–1200. ISBN 0-8493-8345-5.

External links

• Analog Modulation online interactive demonstration using Python in Google Colab Platform, by C Foh.

Phase Modulation (PM)

This page is about the analog modulation. For the digital version, see Phase-shift keying.

Phase modulation (PM) is a modulation pattern for conditioning communication signals for transmission. It encodes a message signal as variations in the instantaneous phase of a carrier wave. Phase modulation is one of the two principal forms of angle modulation, together with frequency modulation.

In phase modulation, the instantaneous amplitude of the baseband signal modifies the phase of the carrier signal keeping its amplitude and frequency constant. The phase of a carrier signal is modulated to follow the changing signal level (amplitude) of the message signal. The peak amplitude and the frequency of the carrier signal are maintained constant, but as the amplitude of the message signal changes, the phase of the carrier changes correspondingly.

Phase modulation is an integral part of many digital transmission coding schemes that underlie a wide range of technologies like Wi-Fi, GSM and satellite television. However it is not widely used for transmitting analog audio signals via radio waves. It is also used for signal and waveform generation in digital synthesizers, such as the Yamaha DX7, to implement FM synthesis. A related type of sound synthesis called phase distortion is used in the Casio CZ synthesizers.

Foundation

In general form, an analog modulation process of a sinusoidal carrier wave may be described by the following equation:

$m(t)=A(t)\cdot \cos(\omega t+\phi (t))\,$.

A(t) represents the time-varying amplitude of the sinusoidal carrier wave and the cosine-term is the carrier at its angular frequency $\omega$, and the instantaneous phase deviation $\phi (t)$. This description directly provides the two major groups of modulation, amplitude modulation and angle modulation. In amplitude modulation, the angle term is held constant, while in angle modulation the term A(t) is constant and the second term of the equation has a functional relationship to the modulating message signal.

The functional form of the cosine term, which contains the expression of the instantaneous phase $\omega t+\phi (t)$ as its argument, provides the distinction of the two types of angle modulation, frequency modulation (FM) and phase modulation (PM).

The modulating wave (blue) is modulating the carrier wave (red), resulting the PM signal (green).

  g(t) = ⁠ π /2⁠×sin[ 2×2π t + ⁠ π /2⁠×sin( 3×2π t ) ]  

In FM the message signal causes a functional variation of the carrier frequency. These variations are controlled by both the frequency and the amplitude of the modulating wave.

In phase modulation, the instantaneous phase deviation $\phi (t)$ (phase angle) of the carrier is controlled by the modulating waveform, such that the principal frequency remains constant.

In principle, the modulating signal in both frequency and phase modulation may either be analog in nature, or it may be digital.

The mathematics of the spectral behaviour reveals that there are two regions of particular interest:

• For small amplitude signals, PM is similar to amplitude modulation (AM) and exhibits its unfortunate doubling of baseband bandwidth and poor efficiency.
• For a single large sinusoidal signal, PM is similar to FM, and its bandwidth is approximately

  $2\left(h+1\right)f_{\text{M}}$,

  Where $f_{\text{M}}=\omega _{\text{m}}/2\pi$ and $h$ is the modulation index defined below. This is also known as Carson's Rule for PM.

Modulation index

As with other modulation indices, this quantity indicates by how much the modulated variable varies around its unmodulated level. It relates to the variations in the phase of the carrier signal:

$h=\Delta \theta ,$

where $\Delta \theta$ is the peak phase deviation. Compare to the modulation index for frequency modulation.

See also

• Automatic frequency control
• Modulation for a list of other modulation techniques
• Modulation sphere
• Polar modulation
• Electro-optic modulator for Pockel's Effect phase modulation for applying sidebands to a monochromatic wave

Quadrature Amplitude Modulation (QAM)

"QAM" redirects here. For the digital television standard, see QAM (television). For other uses, see QAM (disambiguation).

Quadrature amplitude modulation (QAM) is the name of a family of digital modulation methods and a related family of analog modulation methods widely used in modern telecommunications to transmit information. It conveys two analog message signals, or two digital bit streams, by changing (modulating) the amplitudes of two carrier waves, using the amplitude-shift keying (ASK) digital modulation scheme or amplitude modulation (AM) analog modulation scheme. The two carrier waves are of the same frequency and are out of phase with each other by 90°, a condition known as orthogonality or quadrature. The transmitted signal is created by adding the two carrier waves together. At the receiver, the two waves can be coherently separated (demodulated) because of their orthogonality. Another key property is that the modulations are low-frequency/low-bandwidth waveforms compared to the carrier frequency, which is known as the narrowband assumption.

Phase modulation (analog PM) and phase-shift keying (digital PSK) can be regarded as a special case of QAM, where the amplitude of the transmitted signal is a constant, but its phase varies. This can also be extended to frequency modulation (FM) and frequency-shift keying (FSK), for these can be regarded as a special case of phase modulation.

QAM is used extensively as a modulation scheme for digital communications systems, such as in 802.11 Wi-Fi standards. Arbitrarily high spectral efficiencies can be achieved with QAM by setting a suitable constellation size, limited only by the noise level and linearity of the communications channel.  QAM is being used in optical fiber systems as bit rates increase; QAM16 and QAM64 can be optically emulated with a three-path interferometer.

Demodulation

Analog QAM: PAL color bar signal on a Vectorscope

In a QAM signal, one carrier lags the other by 90°, and its amplitude modulation is customarily referred to as the in-phase component, denoted by I(t). The other modulating function is the quadrature component, Q(t). So the composite waveform is mathematically modeled as:

$s_{s}(t)\triangleq \sin(2\pi f_{c}t)I(t)\ +\ \underbrace {\sin \left(2\pi f_{c}t+{\tfrac {\pi }{2}}\right)} _{\cos \left(2\pi f_{c}t\right)}\;Q(t),$     or:

$s_{c}(t)\triangleq \cos(2\pi f_{c}t)I(t)\ +\ \underbrace {\cos \left(2\pi f_{c}t+{\tfrac {\pi }{2}}\right)} _{-\sin \left(2\pi f_{c}t\right)}\;Q(t),$ (Eq.1)

where f_c is the carrier frequency.  At the receiver, a coherent demodulator multiplies the received signal separately with both a cosine and sine signal to produce the received estimates of I(t) and Q(t). For example:

$r(t)\triangleq s_{c}(t)\cos(2\pi f_{c}t)=I(t)\cos(2\pi f_{c}t)\cos(2\pi f_{c}t)-Q(t)\sin(2\pi f_{c}t)\cos(2\pi f_{c}t).$

Using standard trigonometric identities, we can write this as:

${\begin{aligned}r(t)&={\tfrac {1}{2}}I(t)\left[1+\cos(4\pi f_{c}t)\right]-{\tfrac {1}{2}}Q(t)\sin(4\pi f_{c}t)\\&={\tfrac {1}{2}}I(t)+{\tfrac {1}{2}}\left[I(t)\cos(4\pi f_{c}t)-Q(t)\sin(4\pi f_{c}t)\right].\end{aligned}}$

Low-pass filtering r(t) removes the high frequency terms (containing 4πf_ct), leaving only the I(t) term. This filtered signal is unaffected by Q(t), showing that the in-phase component can be received independently of the quadrature component.  Similarly, we can multiply s_c(t) by a sine wave and then low-pass filter to extract Q(t).

The graphs of the sine (solid red) and cosine (dotted blue) functions are sinusoids of different phases.

The addition of two sinusoids is a linear operation that creates no new frequency components. So the bandwidth of the composite signal is comparable to the bandwidth of the DSB (double-sideband) components. Effectively, the spectral redundancy of DSB enables a doubling of the information capacity using this technique. This comes at the expense of demodulation complexity. In particular, a DSB signal has zero-crossings at a regular frequency, which makes it easy to recover the phase of the carrier sinusoid. It is said to be self-clocking. But the sender and receiver of a quadrature-modulated signal must share a clock or otherwise send a clock signal. If the clock phases drift apart, the demodulated I and Q signals bleed into each other, yielding crosstalk. In this context, the clock signal is called a "phase reference". Clock synchronization is typically achieved by transmitting a burst subcarrier or a pilot signal. The phase reference for NTSC, for example, is included within its colorburst signal.

Analog QAM is used in:

• NTSC and PAL analog color television systems, where the I- and Q-signals carry the components of chroma (colour) information. The QAM carrier phase is recovered from a special colorburst transmitted at the beginning of each scan line.
• C-QUAM ("Compatible QAM") is used in AM stereo radio to carry the stereo difference information.

Fourier analysis

Applying Euler's formula to the sinusoids in Eq.1, the positive-frequency portion of s_c (or analytic representation) is:

$s_{c}(t)_{+}={\tfrac {1}{2}}e^{i2\pi f_{c}t}[I(t)+iQ(t)]\quad {\stackrel {\mathcal {F}}{\Longrightarrow }}\quad {\tfrac {1}{2}}\left[{\widehat {I\ }}(f-f_{c})+e^{i\pi /2}{\widehat {Q}}(f-f_{c})\right],$

where ${\mathcal {F}}$ denotes the Fourier transform, and ︿I and ︿Q are the transforms of I(t) and Q(t). This result represents the sum of two DSB-SC signals with the same center frequency. The factor of i (= e^iπ/2) represents the 90° phase shift that enables their individual demodulations.

Digital QAM

Digital 16-QAM with example symbols

Constellation points for 4-QAM, 16-QAM, 32-QAM, and 64-QAM overlapped

As in many digital modulation schemes, the constellation diagram is useful for QAM. In QAM, the constellation points are usually arranged in a square grid with equal vertical and horizontal spacing, although other configurations are possible (e.g. a hexagonal or triangular grid). In digital telecommunications the data is usually binary, so the number of points in the grid is typically a power of 2 (2, 4, 8, …), corresponding to the number of bits per symbol. The simplest and most commonly used QAM constellations consist of points arranged in a square, i.e. 16-QAM, 64-QAM and 256-QAM (even powers of two). Non-square constellations, such as Cross-QAM, can offer greater efficiency but are rarely used because of the cost of increased modem complexity.

By moving to a higher-order constellation, it is possible to transmit more bits per symbol. However, if the mean energy of the constellation is to remain the same (by way of making a fair comparison), the points must be closer together and are thus more susceptible to noise and other corruption; this results in a higher bit error rate and so higher-order QAM can deliver more data less reliably than lower-order QAM, for constant mean constellation energy. Using higher-order QAM without increasing the bit error rate requires a higher signal-to-noise ratio (SNR) by increasing signal energy, reducing noise, or both.

If data rates beyond those offered by 8-PSK are required, it is more usual to move to QAM since it achieves a greater distance between adjacent points in the I-Q plane by distributing the points more evenly. The complicating factor is that the points are no longer all the same amplitude and so the demodulator must now correctly detect both phase and amplitude, rather than just phase.

64-QAM and 256-QAM are often used in digital cable television and cable modem applications. In the United States, 64-QAM and 256-QAM are the mandated modulation schemes for digital cable (see QAM tuner) as standardised by the SCTE in the standard ANSI/SCTE 07 2013. In the UK, 64-QAM is used for digital terrestrial television (Freeview) whilst 256-QAM is used for Freeview-HD.

Bit-loading (bits per QAM constellation) on an ADSL line

Communication systems designed to achieve very high levels of spectral efficiency usually employ very dense QAM constellations. For example, current Homeplug AV2 500-Mbit/s powerline Ethernet devices use 1024-QAM and 4096-QAM, as well as future devices using ITU-T G.hn standard for networking over existing home wiring (coaxial cable, phone lines and power lines); 4096-QAM provides 12 bits/symbol. Another example is ADSL technology for copper twisted pairs, whose constellation size goes up to 32768-QAM (in ADSL terminology this is referred to as bit-loading, or bit per tone, 32768-QAM being equivalent to 15 bits per tone).

Ultra-high capacity microwave backhaul systems also use 1024-QAM. With 1024-QAM, adaptive coding and modulation (ACM) and XPIC, vendors can obtain gigabit capacity in a single 56 MHz channel.

Interference and noise

In moving to a higher order QAM constellation (higher data rate and mode) in hostile RF/microwave QAM application environments, such as in broadcasting or telecommunications, multipath interference typically increases. There is a spreading of the spots in the constellation, decreasing the separation between adjacent states, making it difficult for the receiver to decode the signal appropriately. In other words, there is reduced noise immunity. There are several test parameter measurements which help determine an optimal QAM mode for a specific operating environment. The following three are most significant:

• Carrier/interference ratio
• Carrier-to-noise ratio
• Threshold-to-noise ratio

See also

• Amplitude and phase-shift keying or asymmetric phase-shift keying (APSK)
• Carrierless amplitude phase modulation (CAP)
• Circle packing § Applications
• In-phase and quadrature components
• Modulation for other examples of modulation techniques
• Phase-shift keying
• QAM tuner for HDTV
• Random modulation

Further reading

• Jonqyin (Russell) Sun "Linear diversity analysis for QAM in Rician fading channels", IEEE WOCC 2014
• John G. Proakis, "Digital Communications, 3rd Edition"

External links

• QAM Demodulation
• Interactive webdemo of QAM constellation with additive noise Institute of Telecommunicatons, University of Stuttgart
• QAM bit error rate for AWGN channel – online experiment
• How imperfections affect QAM constellation
• Microwave Phase Shifters Overview by Herley General Microwave
• Simulation of dual-polarization QPSK (DP-QPSK) for 100G optical transmission

Space Modulation (SM)

Space modulation is a radio amplitude modulation technique used in instrument landing systems (ILS) that incorporates the use of multiple antennas fed with various radio frequency powers and phases to create different depths of modulation within various volumes of three-dimensional airspace. This modulation method differs from internal modulation methods inside most other radio transmitters in that the phases and powers of the two individual signals mix within airspace, rather than in a modulator.

An aircraft with an on-board ILS receiver within the capture area of an ILS, (glideslope and localizer range), will detect varying depths of modulation according to the aircraft's position within that airspace, providing accurate positional information about the progress to the threshold.

Method used to determine aircraft position

The ILS uses two radio frequencies, one for each ground station (about 110 MHz for LOC and 330 MHz for the GS), to transmit two amplitude-modulated signals (90 Hz and 150 Hz), along the glidepath (GS) and the course (LOC) trajectories into airspace. It is this signal that is projected up from the runway which an aircraft employing an instrument approach uses to land.

The modulation depth of each 90 Hz and 150 Hz signal changes according to the deviation of the aircraft from the correct position for the aircraft to touchdown on the threshold. The difference between the two signal modulation depths is zero when the aircraft is on the correct course and glidepath on approach to the runway—i.e. No difference (zero DDM), produces no deviation from the middle indication of the instrument's needle within the cockpit of the aircraft.

See also

• Difference in the Depth of Modulation
• Instrument Landing System

Single-Sideband Modulation (SSB)

Illustration of the spectrum of AM and SSB signals. The lower side band (LSB) spectrum is inverted compared to the baseband. As an example, a 2 kHz audio baseband signal modulated onto a 5 MHz carrier will produce a frequency of 5.002 MHz if upper side band (USB) is used or 4.998 MHz if LSB is used.

In radio communications, single-sideband modulation (SSB) or single-sideband suppressed-carrier modulation (SSB-SC) is a type of modulation used to transmit information, such as an audio signal, by radio waves. A refinement of amplitude modulation, it uses transmitter power and bandwidth more efficiently. Amplitude modulation produces an output signal the bandwidth of which is twice the maximum frequency of the original baseband signal. Single-sideband modulation avoids this bandwidth increase, and the power wasted on a carrier, at the cost of increased device complexity and more difficult tuning at the receiver.

Basic concept

Radio transmitters work by mixing a radio frequency (RF) signal of a specific frequency, the carrier wave, with the audio signal to be broadcast. In AM transmitters this mixing usually takes place in the final RF amplifier (high level modulation). It is less common and much less efficient to do the mixing at low power and then amplify it in a linear amplifier. Either method produces a set of frequencies with a strong signal at the carrier frequency and with weaker signals at frequencies extending above and below the carrier frequency by the maximum frequency of the input signal. Thus the resulting signal has a spectrum whose bandwidth is twice the maximum frequency of the original input audio signal.

SSB takes advantage of the fact that the entire original signal is encoded in each of these "sidebands". Since a good receiver can extract the complete original signal from either the upper or lower sideband, it is not essential to transmit both sidebands plus the carrier. There are several methods for eliminating the carrier and one sideband from the transmitted signal. Producing this single sideband signal can be done at high level in the final amplifier stage as with AM but it is usually produced at a low power level and linearly amplified. The lower efficiency of linear amplification partially offsets the power advantage gained by eliminating the carrier and one sideband. Nevertheless, SSB transmissions use the available amplifier energy considerably more efficiently, providing longer-range transmission for the same power output. In addition, the occupied spectrum is less than half that of a full carrier AM signal.

SSB reception requires frequency stability and selectivity well beyond that of inexpensive AM receivers which is why broadcasters have seldom used it. In point-to-point communications where expensive receivers are in common use already they can successfully be adjusted to receive whichever sideband is being transmitted.

History

The first U.S. patent application for SSB modulation was filed on December 1, 1915, by John Renshaw Carson. The U.S. Navy experimented with SSB over its radio circuits before World War I. SSB first entered commercial service on January 7, 1927, on the longwave transatlantic public radiotelephone circuit between New York and London. The high power SSB transmitters were located at Rocky Point, New York, and Rugby, England. The receivers were in very quiet locations in Houlton, Maine, and Cupar, Scotland.

SSB was also used over long-distance telephone lines, as part of a technique known as frequency-division multiplexing (FDM). FDM was pioneered by telephone companies in the 1930s. With this technology, many simultaneous voice channels could be transmitted on a single physical circuit, for example in L-carrier. With SSB, channels could be spaced (usually) only 4,000 Hz apart, while offering a speech bandwidth of nominally 300 Hz to 3,400 Hz.

Amateur radio operators began serious experimentation with SSB after World War II. The Strategic Air Command established SSB as the radio standard for its aircraft in 1957. It has become a de facto standard for long-distance voice radio transmissions since then.

Mathematical formulation

Frequency-domain depiction of the mathematical steps that convert a baseband function into a single-sideband radio signal

Single-sideband has the mathematical form of quadrature amplitude modulation (QAM) in the special case where one of the baseband waveforms is derived from the other, instead of being independent messages:

$s_{\text{ssb}}(t)=s(t)\cdot \cos \left(2\pi f_{0}t\right)-{\widehat {s}}(t)\cdot \sin \left(2\pi f_{0}t\right),\,$ (Eq.1)

where $s(t)\,$ is the message (real-valued), ${\widehat {s}}(t)\,$ is its Hilbert transform, and $f_{0}\,$ is the radio carrier frequency.

To understand this formula, we may express $s(t)$ as the real part of a complex-valued function, with no loss of information:

$s(t)=\operatorname {Re} \left\{s_{\mathrm {a} }(t)\right\}=\operatorname {Re} \left\{s(t)+j\cdot {\widehat {s}}(t)\right\},$

where $j$ represents the imaginary unit.  $s_{\mathrm {a} }(t)$ is the analytic representation of $s(t),$  which means that it comprises only the positive-frequency components of $s(t)$:

${\frac {1}{2}}S_{\mathrm {a} }(f)={\begin{cases}S(f),&{\text{for}}\ f>0,\\0,&{\text{for}}\ f<0,\end{cases}}$

where $S_{\mathrm {a} }(f)$ and $S(f)$ are the respective Fourier transforms of $s_{\mathrm {a} }(t)$ and $s(t).$  Therefore, the frequency-translated function $S_{\mathrm {a} }\left(f-f_{0}\right)$ contains only one side of $S(f).$  Since it also has only positive-frequency components, its inverse Fourier transform is the analytic representation of $s_{\text{ssb}}(t):$

$s_{\text{ssb}}(t)+j\cdot {\widehat {s}}_{\text{ssb}}(t)={\mathcal {F}}^{-1}\{S_{\mathrm {a} }\left(f-f_{0}\right)\}=s_{\mathrm {a} }(t)\cdot e^{j2\pi f_{0}t},\,$

and again the real part of this expression causes no loss of information.  With Euler's formula to expand  $e^{j2\pi f_{0}t},\,$  we obtain Eq.1:

${\begin{aligned}s_{\text{ssb}}(t)&=\operatorname {Re} \left\{s_{\mathrm {a} }(t)\cdot e^{j2\pi f_{0}t}\right\}\\&=\operatorname {Re} \left\{\,\left[s(t)+j\cdot {\widehat {s}}(t)\right]\cdot \left[\cos \left(2\pi f_{0}t\right)+j\cdot \sin \left(2\pi f_{0}t\right)\right]\,\right\}\\&=s(t)\cdot \cos \left(2\pi f_{0}t\right)-{\widehat {s}}(t)\cdot \sin \left(2\pi f_{0}t\right).\end{aligned}}$

Coherent demodulation of $s_{\text{ssb}}(t)$ to recover $s(t)$ is the same as AM: multiply by $\cos \left(2\pi f_{0}t\right),$  and lowpass to remove the "double-frequency" components around frequency $2f_{0}$. If the demodulating carrier is not in the correct phase (cosine phase here), then the demodulated signal will be some linear combination of $s(t)$ and ${\widehat {s}}(t)$, which is usually acceptable in voice communications (if the demodulation carrier frequency is not quite right, the phase will be drifting cyclically, which again is usually acceptable in voice communications if the frequency error is small enough, and amateur radio operators are sometimes tolerant of even larger frequency errors that cause unnatural-sounding pitch shifting effects).

Lower sideband

$s(t)$ can also be recovered as the real part of the complex-conjugate, $s_{\mathrm {a} }^{*}(t),$ which represents the negative frequency portion of $S(f).$ When $f_{0}\,$ is large enough that $S\left(f-f_{0}\right)$ has no negative frequencies, the product $s_{\mathrm {a} }^{*}(t)\cdot e^{j2\pi f_{0}t}$ is another analytic signal, whose real part is the actual lower-sideband transmission:

${\begin{aligned}s_{\mathrm {a} }^{*}(t)\cdot e^{j2\pi f_{0}t}&=s_{\text{lsb}}(t)+j\cdot {\widehat {s}}_{\text{lsb}}(t)\\\Rightarrow s_{\text{lsb}}(t)&=\operatorname {Re} \left\{s_{\mathrm {a} }^{*}(t)\cdot e^{j2\pi f_{0}t}\right\}\\&=s(t)\cdot \cos \left(2\pi f_{0}t\right)+{\widehat {s}}(t)\cdot \sin \left(2\pi f_{0}t\right).\end{aligned}}$

The sum of the two sideband signals is:

$s_{\text{usb}}(t)+s_{\text{lsb}}(t)=2s(t)\cdot \cos \left(2\pi f_{0}t\right),\,$

which is the classic model of suppressed-carrier double sideband AM.

Practical implementations

A Collins KWM-1, an early Amateur Radio transceiver that featured SSB voice capability

Bandpass filtering

One method of producing an SSB signal is to remove one of the sidebands via filtering, leaving only either the upper sideband (USB), the sideband with the higher frequency, or less commonly the lower sideband (LSB), the sideband with the lower frequency. Most often, the carrier is reduced or removed entirely (suppressed), being referred to in full as single sideband suppressed carrier (SSBSC). Assuming both sidebands are symmetric, which is the case for a normal AM signal, no information is lost in the process. Since the final RF amplification is now concentrated in a single sideband, the effective power output is greater than in normal AM (the carrier and redundant sideband account for well over half of the power output of an AM transmitter). Though SSB uses substantially less bandwidth and power, it cannot be demodulated by a simple envelope detector like standard AM.

Hartley modulator

An alternate method of generation known as a Hartley modulator, named after R. V. L. Hartley, uses phasing to suppress the unwanted sideband. To generate an SSB signal with this method, two versions of the original signal are generated, mutually 90° out of phase for any single frequency within the operating bandwidth. Each one of these signals then modulates carrier waves (of one frequency) that are also 90° out of phase with each other. By either adding or subtracting the resulting signals, a lower or upper sideband signal results. A benefit of this approach is to allow an analytical expression for SSB signals, which can be used to understand effects such as synchronous detection of SSB.

Shifting the baseband signal 90° out of phase cannot be done simply by delaying it, as it contains a large range of frequencies. In analog circuits, a wideband 90-degree phase-difference network is used. The method was popular in the days of vacuum tube radios, but later gained a bad reputation due to poorly adjusted commercial implementations. Modulation using this method is again gaining popularity in the homebrew and DSP fields. This method, utilizing the Hilbert transform to phase shift the baseband audio, can be done at low cost with digital circuitry.

Weaver modulator

Another variation, the Weaver modulator, uses only lowpass filters and quadrature mixers, and is a favored method in digital implementations.

In Weaver's method, the band of interest is first translated to be centered at zero, conceptually by modulating a complex exponential $\exp(j\omega t)$ with frequency in the middle of the voiceband, but implemented by a quadrature pair of sine and cosine modulators at that frequency (e.g. 2 kHz). This complex signal or pair of real signals is then lowpass filtered to remove the undesired sideband that is not centered at zero. Then, the single-sideband complex signal centered at zero is upconverted to a real signal, by another pair of quadrature mixers, to the desired center frequency.

Full, reduced, and suppressed-carrier SSB

Conventional amplitude-modulated signals can be considered wasteful of power and bandwidth because they contain a carrier signal and two identical sidebands. Therefore, SSB transmitters are generally designed to minimize the amplitude of the carrier signal. When the carrier is removed from the transmitted signal, it is called suppressed-carrier SSB.

However, in order for a receiver to reproduce the transmitted audio without distortion, it must be tuned to exactly the same frequency as the transmitter. Since this is difficult to achieve in practice, SSB transmissions can sound unnatural, and if the error in frequency is great enough, it can cause poor intelligibility. In order to correct this, a small amount of the original carrier signal can be transmitted so that receivers with the necessary circuitry to synchronize with the transmitted carrier can correctly demodulate the audio. This mode of transmission is called reduced-carrier single-sideband.

In other cases, it may be desirable to maintain some degree of compatibility with simple AM receivers, while still reducing the signal's bandwidth. This can be accomplished by transmitting single-sideband with a normal or slightly reduced carrier. This mode is called compatible (or full-carrier) SSB or amplitude modulation equivalent (AME). In typical AME systems, harmonic distortion can reach 25%, and intermodulation distortion can be much higher than normal, but minimizing distortion in receivers with envelope detectors is generally considered less important than allowing them to produce intelligible audio.

A second, and perhaps more correct, definition of "compatible single sideband" (CSSB) refers to a form of amplitude and phase modulation in which the carrier is transmitted along with a series of sidebands that are predominantly above or below the carrier term. Since phase modulation is present in the generation of the signal, energy is removed from the carrier term and redistributed into the sideband structure similar to that which occurs in analog frequency modulation. The signals feeding the phase modulator and the envelope modulator are further phase-shifted by 90° with respect to each other. This places the information terms in quadrature with each other; the Hilbert transform of information to be transmitted is utilized to cause constructive addition of one sideband and cancellation of the opposite primary sideband. Since phase modulation is employed, higher-order terms are also generated. Several methods have been employed to reduce the impact (amplitude) of most of these higher-order terms. In one system, the phase-modulated term is actually the log of the value of the carrier level plus the phase-shifted audio/information term. This produces an ideal CSSB signal, where at low modulation levels only a first-order term on one side of the carrier is predominant. As the modulation level is increased, the carrier level is reduced while a second-order term increases substantially in amplitude. At the point of 100% envelope modulation, 6 dB of power is removed from the carrier term, and the second-order term is identical in amplitude to carrier term. The first-order sideband has increased in level until it is now at the same level as the formerly unmodulated carrier. At the point of 100% modulation, the spectrum appears identical to a normal double-sideband AM transmission, with the center term (now the primary audio term) at a 0 dB reference level, and both terms on either side of the primary sideband at −6 dB. The difference is that what appears to be the carrier has shifted by the audio-frequency term towards the "sideband in use". At levels below 100% modulation, the sideband structure appears quite asymmetric. When voice is conveyed by a CSSB source of this type, low-frequency components are dominant, while higher-frequency terms are lower by as much as 20 dB at 3 kHz. The result is that the signal occupies approximately 1/2 the normal bandwidth of a full-carrier, DSB signal. There is one catch: the audio term utilized to phase-modulate the carrier is generated based on a log function that is biased by the carrier level. At negative 100% modulation, the term is driven to zero (0), and the modulator becomes undefined. Strict modulation control must be employed to maintain stability of the system and avoid splatter. This system is of Russian origin and was described in the late 1950s. It is uncertain whether it was ever deployed.

A second series of approaches was designed and patented by Leonard R. Kahn. The various Kahn systems removed the hard limit imposed by the use of the strict log function in the generation of the signal. Earlier Kahn systems utilized various methods to reduce the second-order term through the insertion of a predistortion component. One example of this method was also used to generate one of the Kahn independent-sideband (ISB) AM stereo signals. It was known as the STR-77 exciter method, having been introduced in 1977. Later, the system was further improved by use of an arcsine-based modulator that included a 1-0.52E term in the denominator of the arcsin generator equation. E represents the envelope term; roughly half the modulation term applied to the envelope modulator is utilized to reduce the second-order term of the arcsin "phase"-modulated path; thus reducing the second-order term in the undesired sideband. A multi-loop modulator/demodulator feedback approach was used to generate an accurate arcsin signal. This approach was introduced in 1984 and became known as the STR-84 method. It was sold by Kahn Research Laboratories; later, Kahn Communications, Inc. of NY. An additional audio processing device further improved the sideband structure by selectively applying pre-emphasis to the modulating signals. Since the envelope of all the signals described remains an exact copy of the information applied to the modulator, it can be demodulated without distortion by an envelope detector such as a simple diode. In a practical receiver, some distortion may be present, usually at a low level (in AM broadcast, always below 5%), due to sharp filtering and nonlinear group delay in the IF filters of the receiver, which act to truncate the compatibility sideband – those terms that are not the result of a linear process of simply envelope modulating the signal as would be the case in full-carrier DSB-AM – and rotation of phase of these compatibility terms such that they no longer cancel the quadrature distortion term caused by a first-order SSB term along with the carrier. The small amount of distortion caused by this effect is generally quite low and acceptable.

The Kahn CSSB method was also briefly used by Airphone as the modulation method employed for early consumer telephone calls that could be placed from an aircraft to ground. This was quickly supplanted by digital modulation methods to achieve even greater spectral efficiency.

While CSSB is seldom used today in the AM/MW broadcast bands worldwide, some amateur radio operators still experiment with it.

Demodulation

Main article: Demodulation

The front end of an SSB receiver is similar to that of an AM or FM receiver, consisting of a superheterodyne RF front end that produces a frequency-shifted version of the radio frequency (RF) signal within a standard intermediate frequency (IF) band.

To recover the original signal from the IF SSB signal, the single sideband must be frequency-shifted down to its original range of baseband frequencies, by using a product detector which mixes it with the output of a beat frequency oscillator (BFO). In other words, it is just another stage of heterodyning. For this to work, the BFO frequency must be exactly adjusted. If the BFO frequency is off, the output signal will be frequency-shifted (up or down), making speech sound strange and "Donald Duck"-like, or unintelligible.

For audio communications, there is a common agreement about the BFO oscillator shift of 1.7 kHz. A voice signal is sensitive to about 50 Hz shift, with up to 100 Hz still bearable. Some receivers use a carrier recovery system, which attempts to automatically lock on to the exact IF frequency. The carrier recovery doesn't solve the frequency shift. It gives better S/N ratio on the detector output.

As an example, consider an IF SSB signal centered at frequency $F_{\text{if}}\,$ = 45000 Hz. The baseband frequency it needs to be shifted to is $F_{b}\,$ = 2000 Hz. The BFO output waveform is $\cos \left(2\pi \cdot F_{\text{bfo}}\cdot t\right)$. When the signal is multiplied by (aka heterodyned with) the BFO waveform, it shifts the signal to  $\left(F_{\text{if}}+F_{\text{bfo}}\right)$, and to $\left|F_{\text{if}}-F_{\text{bfo}}\right|$, which is known as the beat frequency or image frequency. The objective is to choose an $F_{\text{bfo}}$ that results in  $\left|F_{\text{if}}-F_{\text{bfo}}\right|=F_{b}\,$ = 2000 Hz. (The unwanted components at $\left(F_{\text{if}}+F_{\text{bfo}}\right)\,$ can be removed by a lowpass filter; for which an output transducer or the human ear may serve).

There are two choices for $F_{\text{bfo}}$: 43000 Hz and 47000 Hz, called low-side and high-side injection. With high-side injection, the spectral components that were distributed around 45000 Hz will be distributed around 2000 Hz in the reverse order, also known as an inverted spectrum. That is in fact desirable when the IF spectrum is also inverted, because the BFO inversion restores the proper relationships. One reason for that is when the IF spectrum is the output of an inverting stage in the receiver. Another reason is when the SSB signal is actually a lower sideband, instead of an upper sideband. But if both reasons are true, then the IF spectrum is not inverted, and the non-inverting BFO (43000 Hz) should be used.

If $F_{\text{bfo}}\,$ is off by a small amount, then the beat frequency is not exactly $F_{b}\,$, which can lead to the speech distortion mentioned earlier.

SSB as a speech-scrambling technique

SSB techniques can also be adapted to frequency-shift and frequency-invert baseband waveforms (voice inversion). This voice scrambling method was made by running the audio of one side band modulated audio sample through its opposite (e.g. running an LSB modulated audio sample through a radio running USB modulation). These effects were used, in conjunction with other filtering techniques, during World War II as a simple method for speech encryption. Radiotelephone conversations between the US and Britain were intercepted and "decrypted" by the Germans; they included some early conversations between Franklin D. Roosevelt and Churchill. In fact, the signals could be understood directly by trained operators. Largely to allow secure communications between Roosevelt and Churchill, the SIGSALY system of digital encryption was devised.

Today, such simple inversion-based speech encryption techniques are easily decrypted using simple techniques and are no longer regarded as secure.

Vestigial sideband (VSB)

VSB modulation

Limitation of single-sideband modulation being used for voice signals and not available for video/TV signals leads to the usage of vestigial sideband. A vestigial sideband (in radio communication) is a sideband that has been only partly cut off or suppressed. Television broadcasts (in analog video formats) use this method if the video is transmitted in AM, due to the large bandwidth used. It may also be used in digital transmission, such as the ATSC standardized 8VSB.

The broadcast or transport channel for TV in countries that use NTSC or ATSC has a bandwidth of 6 MHz. To conserve bandwidth, SSB would be desirable, but the video signal has significant low-frequency content (average brightness) and has rectangular synchronising pulses. The engineering compromise is vestigial-sideband transmission. In vestigial sideband, the full upper sideband of bandwidth W2 = 4.0 MHz is transmitted, but only W1 = 0.75 MHz of the lower sideband is transmitted, along with a carrier. The carrier frequency is 1.25 MHz above the lower edge of the 6 MHz wide channel. This effectively makes the system AM at low modulation frequencies and SSB at high modulation frequencies. The absence of the lower sideband components at high frequencies must be compensated for, and this is done in the IF amplifier.

Frequencies for LSB and USB in amateur radio voice communication

When single-sideband is used in amateur radio voice communications, it is common practice that for frequencies below 10 MHz, lower sideband (LSB) is used and for frequencies of 10 MHz and above, upper sideband (USB) is used. For example, on the 40 m band, voice communications often take place around 7.100 MHz using LSB mode. On the 20 m band at 14.200 MHz, USB mode would be used.

An exception to this rule applies to the five discrete amateur channels on the 60-meter band (near 5.3 MHz) where FCC rules specifically require USB.

Extended single sideband (eSSB)

Extended single sideband is any J3E (SSB-SC) mode that exceeds the audio bandwidth of standard or traditional 2.9 kHz SSB J3E modes (ITU 2K90J3E) to support higher-quality sound.

Extended SSB modes	Bandwidth	Frequency response	ITU Designator
eSSB (Narrow-1a)	3 kHz	100 Hz ~ 3.10 kHz	3K00J3E
eSSB (Narrow-1b)	3 kHz	50 Hz ~ 3.05 kHz	3K00J3E
eSSB (Narrow-2)	3.5 kHz	50 Hz ~ 3.55 kHz	3K50J3E
eSSB (Medium-1)	4 kHz	50 Hz ~ 4.05 kHz	4K00J3E
eSSB (Medium-2)	4.5 kHz	50 Hz ~ 4.55 kHz	4K50J3E
eSSB (Wide-1)	5 kHz	50 Hz ~ 5.05 kHz	5K00J3E
eSSB (Wide-2)	6 kHz	50 Hz ~ 6.05 kHz	6K00J3E

Amplitude-companded single-sideband modulation (ACSSB)

Amplitude-companded single sideband (ACSSB) is a narrowband modulation method using a single sideband with a pilot tone, allowing an expander in the receiver to restore the amplitude that was severely compressed by the transmitter. It offers improved effective range over standard SSB modulation while simultaneously retaining backwards compatibility with standard SSB radios. ACSSB also offers reduced bandwidth and improved range for a given power level compared with narrow band FM modulation.

Controlled-envelope single-sideband modulation (CESSB)

The generation of standard SSB modulation results in large envelope overshoots well above the average envelope level for a sinusoidal tone (even when the audio signal is peak-limited). The standard SSB envelope peaks are due to truncation of the spectrum and nonlinear phase distortion from the approximation errors of the practical implementation of the required Hilbert transform. It was recently shown that suitable overshoot compensation (so-called controlled-envelope single-sideband modulation or CESSB) achieves about 3.8 dB of peak reduction for speech transmission. This results in an effective average power increase of about 140%. Although the generation of the CESSB signal can be integrated into the SSB modulator, it is feasible to separate the generation of the CESSB signal (e.g. in form of an external speech preprocessor) from a standard SSB radio. This requires that the standard SSB radio's modulator be linear-phase and have a sufficient bandwidth to pass the CESSB signal. If a standard SSB modulator meets these requirements, then the envelope control by the CESSB process is preserved.

ITU designations

In 1982, the International Telecommunication Union (ITU) designated the types of amplitude modulation:

Designation	Description
A3E	Double-sideband full-carrier – the basic amplitude-modulation scheme
R3E	Single-sideband reduced-carrier
H3E	Single-sideband full-carrier
J3E	Single-sideband suppressed-carrier
B8E	Independent-sideband emission
C3F	Vestigial-sideband
Lincompex	Linked compressor and expander

See also

• ACSSB, amplitude-companded single sideband
• Independent sideband
• Modulation for other examples of modulation techniques
• Sideband for more general information about a sideband

Sources

• Partly from Federal Standard 1037C in support of MIL-STD-188

Further reading

• Sgrignoli, G., W. Bretl, R. and Citta. (1995). "VSB modulation used for terrestrial and cable broadcasts." IEEE Transactions on Consumer Electronics. v. 41, issue 3, p. 367 - 382.
• J. Brittain, (1992). "Scanning the past: Ralph V.L. Hartley", Proc. IEEE, vol.80,p. 463.
• eSSB - Extended Single Sideband

Digital Modulation

This page is about the method to imprint data on a carrier used in communications and electrical engineering. For other uses, see Rai282/Books/Modulation (disambiguation).

Categorization for signal modulation based on data and carrier types

In electronics and telecommunications, modulation is the process of varying one or more properties of a periodic waveform, called the carrier signal, with a separate signal called the modulation signal that typically contains information to be transmitted. For example, the modulation signal might be an audio signal representing sound from a microphone, a video signal representing moving images from a video camera, or a digital signal representing a sequence of binary digits, a bitstream from a computer.

This carrier wave usually has a much higher frequency than the message signal does. This is because it is impractical to transmit signals with low frequencies. Generally, to receive a radio wave one needs a radio antenna with length that is one-fourth of wavelength. For low frequency radio waves, wavelength is on the scale of kilometers and building such a large antenna is not practical. In radio communication, the modulated carrier is transmitted through space as a radio wave to a radio receiver.

Another purpose of modulation is to transmit multiple channels of information through a single communication medium, using frequency-division multiplexing (FDM). For example, in cable television (which uses FDM), many carrier signals, each modulated with a different television channel, are transported through a single cable to customers. Since each carrier occupies a different frequency, the channels do not interfere with each other. At the destination end, the carrier signal is demodulated to extract the information bearing modulation signal.

A modulator is a device or circuit that performs modulation. A demodulator (sometimes detector) is a circuit that performs demodulation, the inverse of modulation. A modem (from modulator–demodulator), used in bidirectional communication, can perform both operations. The lower frequency band occupied by the modulation signal is called the baseband, while the higher frequency band occupied by the modulated carrier is called the passband.

In analog modulation, an analog modulation signal is "impressed" on the carrier. Examples are amplitude modulation (AM) in which the amplitude (strength) of the carrier wave is varied by the modulation signal, and frequency modulation (FM) in which the frequency of the carrier wave is varied by the modulation signal. These were the earliest types of modulation, and are used to transmit an audio signal representing sound in AM and FM radio broadcasting. More recent systems use digital modulation, which impresses a digital signal consisting of a sequence of binary digits (bits), a bitstream, on the carrier, by means of mapping bits to elements from a discrete alphabet to be transmitted. This alphabet can consist of a set of real or complex numbers, or sequences, like oscillations of different frequencies, so-called frequency-shift keying (FSK) modulation. A more complicated digital modulation method that employs multiple carriers, orthogonal frequency-division multiplexing (OFDM), is used in WiFi networks, digital radio stations and digital cable television transmission.

Analog modulation methods

A low-frequency message signal (top) may be carried by an AM or FM radio wave.

Waterfall plot of a 146.52 MHz radio carrier, with amplitude modulation by a 1,000 Hz sinusoid. Two strong sidebands at + and - 1 kHz from the carrier frequency are shown.

A carrier, frequency modulated by a 1,000 Hz sinusoid. The modulation index has been adjusted to around 2.4, so the carrier frequency has small amplitude. Several strong sidebands are apparent; in principle an infinite number are produced in FM but the higher-order sidebands are of negligible magnitude.

In analog modulation, the modulation is applied continuously in response to the analog information signal. Common analog modulation techniques include:

• Amplitude modulation (AM) (here the amplitude of the carrier signal is varied in accordance with the instantaneous amplitude of the modulating signal)
  • Double-sideband modulation (DSB)
    • Double-sideband modulation with carrier (DSB-WC) (used on the AM radio broadcasting band)
    • Double-sideband suppressed-carrier transmission (DSB-SC)
    • Double-sideband reduced carrier transmission (DSB-RC)
  • Single-sideband modulation (SSB, or SSB-AM)
    • Single-sideband modulation with carrier (SSB-WC)
    • Single-sideband modulation suppressed carrier modulation (SSB-SC)
  • Vestigial sideband modulation (VSB, or VSB-AM)
  • Quadrature amplitude modulation (QAM)
• Angle modulation, which is approximately constant envelope
  • Frequency modulation (FM) (here the frequency of the carrier signal is varied in accordance with the instantaneous amplitude of the modulating signal)
  • Phase modulation (PM) (here the phase shift of the carrier signal is varied in accordance with the instantaneous amplitude of the modulating signal)
  • Transpositional Modulation (TM), in which the waveform inflection is modified resulting in a signal where each quarter cycle is transposed in the modulation process. TM is a pseudo-analog modulation (AM). Where an AM carrier also carries a phase variable phase f(ǿ). TM is f(AM,ǿ)

Digital modulation methods

In digital modulation, an analog carrier signal is modulated by a discrete signal. Digital modulation methods can be considered as digital-to-analog conversion and the corresponding demodulation or detection as analog-to-digital conversion. The changes in the carrier signal are chosen from a finite number of M alternative symbols (the modulation alphabet).

Schematic of 4 baud, 8 bit/s data link containing arbitrarily chosen values

A simple example: A telephone line is designed for transferring audible sounds, for example, tones, and not digital bits (zeros and ones). Computers may, however, communicate over a telephone line by means of modems, which are representing the digital bits by tones, called symbols. If there are four alternative symbols (corresponding to a musical instrument that can generate four different tones, one at a time), the first symbol may represent the bit sequence 00, the second 01, the third 10 and the fourth 11. If the modem plays a melody consisting of 1000 tones per second, the symbol rate is 1000 symbols/second, or 1000 baud. Since each tone (i.e., symbol) represents a message consisting of two digital bits in this example, the bit rate is twice the symbol rate, i.e. 2000 bits per second.

According to one definition of digital signal, the modulated signal is a digital signal. According to another definition, the modulation is a form of digital-to-analog conversion. Most textbooks would consider digital modulation schemes as a form of digital transmission, synonymous to data transmission; very few would consider it as analog transmission.

Fundamental digital modulation methods

The most fundamental digital modulation techniques are based on keying:

• PSK (phase-shift keying): a finite number of phases are used.
• FSK (frequency-shift keying): a finite number of frequencies are used.
• ASK (amplitude-shift keying): a finite number of amplitudes are used.
• QAM (quadrature amplitude modulation): a finite number of at least two phases and at least two amplitudes are used.

In QAM, an in-phase signal (or I, with one example being a cosine waveform) and a quadrature phase signal (or Q, with an example being a sine wave) are amplitude modulated with a finite number of amplitudes and then summed. It can be seen as a two-channel system, each channel using ASK. The resulting signal is equivalent to a combination of PSK and ASK.

In all of the above methods, each of these phases, frequencies or amplitudes are assigned a unique pattern of binary bits. Usually, each phase, frequency or amplitude encodes an equal number of bits. This number of bits comprises the symbol that is represented by the particular phase, frequency or amplitude.

If the alphabet consists of $M=2^{N}$ alternative symbols, each symbol represents a message consisting of N bits. If the symbol rate (also known as the baud rate) is $f_{S}$ symbols/second (or baud), the data rate is $Nf_{S}$ bit/second.

For example, with an alphabet consisting of 16 alternative symbols, each symbol represents 4 bits. Thus, the data rate is four times the baud rate.

In the case of PSK, ASK or QAM, where the carrier frequency of the modulated signal is constant, the modulation alphabet is often conveniently represented on a constellation diagram, showing the amplitude of the I signal at the x-axis, and the amplitude of the Q signal at the y-axis, for each symbol.

Modulator and detector principles of operation

PSK and ASK, and sometimes also FSK, are often generated and detected using the principle of QAM. The I and Q signals can be combined into a complex-valued signal I+jQ (where j is the imaginary unit). The resulting so called equivalent lowpass signal or equivalent baseband signal is a complex-valued representation of the real-valued modulated physical signal (the so-called passband signal or RF signal).

These are the general steps used by the modulator to transmit data:

1. Group the incoming data bits into codewords, one for each symbol that will be transmitted.
2. Map the codewords to attributes, for example, amplitudes of the I and Q signals (the equivalent low pass signal), or frequency or phase values.
3. Adapt pulse shaping or some other filtering to limit the bandwidth and form the spectrum of the equivalent low pass signal, typically using digital signal processing.
4. Perform digital to analog conversion (DAC) of the I and Q signals (since today all of the above is normally achieved using digital signal processing, DSP).
5. Generate a high-frequency sine carrier waveform, and perhaps also a cosine quadrature component. Carry out the modulation, for example by multiplying the sine and cosine waveform with the I and Q signals, resulting in the equivalent low pass signal being frequency shifted to the modulated passband signal or RF signal. Sometimes this is achieved using DSP technology, for example direct digital synthesis using a waveform table, instead of analog signal processing. In that case, the above DAC step should be done after this step.
6. Amplification and analog bandpass filtering to avoid harmonic distortion and periodic spectrum.

At the receiver side, the demodulator typically performs:

1. Bandpass filtering.
2. Automatic gain control, AGC (to compensate for attenuation, for example fading).
3. Frequency shifting of the RF signal to the equivalent baseband I and Q signals, or to an intermediate frequency (IF) signal, by multiplying the RF signal with a local oscillator sine wave and cosine wave frequency (see the superheterodyne receiver principle).
4. Sampling and analog-to-digital conversion (ADC) (sometimes before or instead of the above point, for example by means of undersampling).
5. Equalization filtering, for example, a matched filter, compensation for multipath propagation, time spreading, phase distortion and frequency selective fading, to avoid intersymbol interference and symbol distortion.
6. Detection of the amplitudes of the I and Q signals, or the frequency or phase of the IF signal.
7. Quantization of the amplitudes, frequencies or phases to the nearest allowed symbol values.
8. Mapping of the quantized amplitudes, frequencies or phases to codewords (bit groups).
9. Parallel-to-serial conversion of the codewords into a bit stream.
10. Pass the resultant bit stream on for further processing such as removal of any error-correcting codes.

As is common to all digital communication systems, the design of both the modulator and demodulator must be done simultaneously. Digital modulation schemes are possible because the transmitter-receiver pair has prior knowledge of how data is encoded and represented in the communications system. In all digital communication systems, both the modulator at the transmitter and the demodulator at the receiver are structured so that they perform inverse operations.

Asynchronous methods do not require a receiver reference clock signal that is phase synchronized with the sender carrier signal. In this case, modulation symbols (rather than bits, characters, or data packets) are asynchronously transferred. The opposite is synchronous modulation.

List of common digital modulation techniques

The most common digital modulation techniques are:

• Phase-shift keying (PSK)
  • Binary PSK (BPSK), using M=2 symbols
  • Quadrature PSK (QPSK), using M=4 symbols
  • 8PSK, using M=8 symbols
  • 16PSK, using M=16 symbols
  • Differential PSK (DPSK)
  • Differential QPSK (DQPSK)
  • Offset QPSK (OQPSK)
  • π/4–QPSK
• Frequency-shift keying (FSK)
  • Audio frequency-shift keying (AFSK)
  • Multi-frequency shift keying (M-ary FSK or MFSK)
  • Dual-tone multi-frequency (DTMF)
• Amplitude-shift keying (ASK)
• On-off keying (OOK), the most common ASK form
  • M-ary vestigial sideband modulation, for example 8VSB
• Quadrature amplitude modulation (QAM), a combination of PSK and ASK
  • Polar modulation like QAM a combination of PSK and ASK
• Continuous phase modulation (CPM) methods
  • Minimum-shift keying (MSK)
  • Gaussian minimum-shift keying (GMSK)
  • Continuous-phase frequency-shift keying (CPFSK)
• Orthogonal frequency-division multiplexing (OFDM) modulation
  • Discrete multitone (DMT), including adaptive modulation and bit-loading
• Wavelet modulation
• Trellis coded modulation (TCM), also known as Trellis modulation
• Spread spectrum techniques
  • Direct-sequence spread spectrum (DSSS)
  • Chirp spread spectrum (CSS) according to IEEE 802.15.4a CSS uses pseudo-stochastic coding
  • Frequency-hopping spread spectrum (FHSS) applies a special scheme for channel release

MSK and GMSK are particular cases of continuous phase modulation. Indeed, MSK is a particular case of the sub-family of CPM known as continuous-phase frequency-shift keying (CPFSK) which is defined by a rectangular frequency pulse (i.e. a linearly increasing phase pulse) of one-symbol-time duration (total response signaling).

OFDM is based on the idea of frequency-division multiplexing (FDM), but the multiplexed streams are all parts of a single original stream. The bit stream is split into several parallel data streams, each transferred over its own sub-carrier using some conventional digital modulation scheme. The modulated sub-carriers are summed to form an OFDM signal. This dividing and recombining help with handling channel impairments. OFDM is considered as a modulation technique rather than a multiplex technique since it transfers one bit stream over one communication channel using one sequence of so-called OFDM symbols. OFDM can be extended to multi-user channel access method in the orthogonal frequency-division multiple access (OFDMA) and multi-carrier code-division multiple access (MC-CDMA) schemes, allowing several users to share the same physical medium by giving different sub-carriers or spreading codes to different users.

Of the two kinds of RF power amplifier, switching amplifiers (Class D amplifiers) cost less and use less battery power than linear amplifiers of the same output power. However, they only work with relatively constant-amplitude-modulation signals such as angle modulation (FSK or PSK) and CDMA, but not with QAM and OFDM. Nevertheless, even though switching amplifiers are completely unsuitable for normal QAM constellations, often the QAM modulation principle are used to drive switching amplifiers with these FM and other waveforms, and sometimes QAM demodulators are used to receive the signals put out by these switching amplifiers.

Automatic digital modulation recognition (ADMR)

Automatic digital modulation recognition in intelligent communication systems is one of the most important issues in software-defined radio and cognitive radio. According to incremental expanse of intelligent receivers, automatic modulation recognition becomes a challenging topic in telecommunication systems and computer engineering. Such systems have many civil and military applications. Moreover, blind recognition of modulation type is an important problem in commercial systems, especially in software-defined radio. Usually in such systems, there are some extra information for system configuration, but considering blind approaches in intelligent receivers, we can reduce information overload and increase transmission performance. Obviously, with no knowledge of the transmitted data and many unknown parameters at the receiver, such as the signal power, carrier frequency and phase offsets, timing information, etc., blind identification of the modulation is made fairly difficult. This becomes even more challenging in real-world scenarios with multipath fading, frequency-selective and time-varying channels.

There are two main approaches to automatic modulation recognition. The first approach uses likelihood-based methods to assign an input signal to a proper class. Another recent approach is based on feature extraction.

Digital baseband modulation

Digital baseband modulation changes the characteristics of a baseband signal, i.e., one without a carrier at a higher frequency.

This can be used as equivalent signal to be later frequency-converted to a carrier frequency, or for direct communication in baseband. The latter methods both involve relatively simple line codes, as often used in local buses, and complicated baseband signalling schemes such as used in DSL.

Pulse modulation methods

Pulse modulation schemes aim at transferring a narrowband analog signal over an analog baseband channel as a two-level signal by modulating a pulse wave. Some pulse modulation schemes also allow the narrowband analog signal to be transferred as a digital signal (i.e., as a quantized discrete-time signal) with a fixed bit rate, which can be transferred over an underlying digital transmission system, for example, some line code. These are not modulation schemes in the conventional sense since they are not channel coding schemes, but should be considered as source coding schemes, and in some cases analog-to-digital conversion techniques.

Analog-over-analog methods

• Pulse-amplitude modulation (PAM)
• Pulse-width modulation (PWM) and pulse-depth modulation (PDM)
• Pulse-frequency modulation (PFM)
• Pulse-position modulation (PPM)

Analog-over-digital methods

• Pulse-code modulation (PCM)
  • Differential PCM (DPCM)
    • Adaptive DPCM (ADPCM)
• Delta modulation (DM or Δ-modulation)
  • Delta-sigma modulation (ΣΔ)
  • Continuously variable slope delta modulation (CVSDM), also called adaptive delta modulation (ADM)
• Pulse-density modulation (PDM)

Miscellaneous modulation techniques

• The use of on-off keying to transmit Morse code at radio frequencies is known as continuous wave (CW) operation.
• Adaptive modulation
• Space modulation is a method whereby signals are modulated within airspace such as that used in instrument landing systems.
• The microwave auditory effect has been pulse modulated with audio waveforms to evoke understandable spoken numbers.

See also

• Channel access methods
• Channel coding
• Codec
• Demodulation
• Electrical resonance
• Heterodyne
• Line code
• Modem
• Modulation order
• Neuromodulation
• RF modulator
• Ring modulation
• Types of radio emissions

Further reading

• Multipliers vs. Modulators Analog Dialogue, June 2013

External links

• Interactive presentation of soft-demapping for AWGN-channel in a web-demo Institute of Telecommunications, University of Stuttgart
• Modem (Modulation and Demodulation)
• CodSim 2.0: Open source Virtual Laboratory for Digital Data Communications Model Department of Computer Architecture, University of Malaga. Simulates Digital line encodings and Digital Modulations. Written in HTML for any web browser.

Amplitude-Shift Keying (ASK)

Amplitude-Shift Keying

Amplitude and Phase-Shift Keying (APSK)

Amplitude and Phase-Shift Keying

Continuous Phase Modulation (CPM)

Continuous Phase Modulation

Frequency-Shift Keying (FSK)

Frequency-Shift Keying

Multiple Frequency-Shift Keying (MFSK)

Multiple Frequency-Shift Keying

Minimum-Shift Keying (MSK)

Minimum-Shift Keying

On–Off Keying (OOK)

On–Off Keying

Pulse-Position Modulation (PPM)

Pulse-Position Modulation

Phase-Shift Keying (PSK)

Phase-Shift Keying

Quadrature Amplitude Modulation (QAM)

"QAM" redirects here. For the digital television standard, see QAM (television). For other uses, see QAM (disambiguation).

Quadrature amplitude modulation (QAM) is the name of a family of digital modulation methods and a related family of analog modulation methods widely used in modern telecommunications to transmit information. It conveys two analog message signals, or two digital bit streams, by changing (modulating) the amplitudes of two carrier waves, using the amplitude-shift keying (ASK) digital modulation scheme or amplitude modulation (AM) analog modulation scheme. The two carrier waves are of the same frequency and are out of phase with each other by 90°, a condition known as orthogonality or quadrature. The transmitted signal is created by adding the two carrier waves together. At the receiver, the two waves can be coherently separated (demodulated) because of their orthogonality. Another key property is that the modulations are low-frequency/low-bandwidth waveforms compared to the carrier frequency, which is known as the narrowband assumption.

Phase modulation (analog PM) and phase-shift keying (digital PSK) can be regarded as a special case of QAM, where the amplitude of the transmitted signal is a constant, but its phase varies. This can also be extended to frequency modulation (FM) and frequency-shift keying (FSK), for these can be regarded as a special case of phase modulation.

QAM is used extensively as a modulation scheme for digital communications systems, such as in 802.11 Wi-Fi standards. Arbitrarily high spectral efficiencies can be achieved with QAM by setting a suitable constellation size, limited only by the noise level and linearity of the communications channel.  QAM is being used in optical fiber systems as bit rates increase; QAM16 and QAM64 can be optically emulated with a three-path interferometer.

Demodulation

Analog QAM: PAL color bar signal on a Vectorscope

In a QAM signal, one carrier lags the other by 90°, and its amplitude modulation is customarily referred to as the in-phase component, denoted by I(t). The other modulating function is the quadrature component, Q(t). So the composite waveform is mathematically modeled as:

$s_{s}(t)\triangleq \sin(2\pi f_{c}t)I(t)\ +\ \underbrace {\sin \left(2\pi f_{c}t+{\tfrac {\pi }{2}}\right)} _{\cos \left(2\pi f_{c}t\right)}\;Q(t),$     or:

$s_{c}(t)\triangleq \cos(2\pi f_{c}t)I(t)\ +\ \underbrace {\cos \left(2\pi f_{c}t+{\tfrac {\pi }{2}}\right)} _{-\sin \left(2\pi f_{c}t\right)}\;Q(t),$ (Eq.1)

where f_c is the carrier frequency.  At the receiver, a coherent demodulator multiplies the received signal separately with both a cosine and sine signal to produce the received estimates of I(t) and Q(t). For example:

$r(t)\triangleq s_{c}(t)\cos(2\pi f_{c}t)=I(t)\cos(2\pi f_{c}t)\cos(2\pi f_{c}t)-Q(t)\sin(2\pi f_{c}t)\cos(2\pi f_{c}t).$

Using standard trigonometric identities, we can write this as:

${\begin{aligned}r(t)&={\tfrac {1}{2}}I(t)\left[1+\cos(4\pi f_{c}t)\right]-{\tfrac {1}{2}}Q(t)\sin(4\pi f_{c}t)\\&={\tfrac {1}{2}}I(t)+{\tfrac {1}{2}}\left[I(t)\cos(4\pi f_{c}t)-Q(t)\sin(4\pi f_{c}t)\right].\end{aligned}}$

Low-pass filtering r(t) removes the high frequency terms (containing 4πf_ct), leaving only the I(t) term. This filtered signal is unaffected by Q(t), showing that the in-phase component can be received independently of the quadrature component.  Similarly, we can multiply s_c(t) by a sine wave and then low-pass filter to extract Q(t).

The graphs of the sine (solid red) and cosine (dotted blue) functions are sinusoids of different phases.

The addition of two sinusoids is a linear operation that creates no new frequency components. So the bandwidth of the composite signal is comparable to the bandwidth of the DSB (double-sideband) components. Effectively, the spectral redundancy of DSB enables a doubling of the information capacity using this technique. This comes at the expense of demodulation complexity. In particular, a DSB signal has zero-crossings at a regular frequency, which makes it easy to recover the phase of the carrier sinusoid. It is said to be self-clocking. But the sender and receiver of a quadrature-modulated signal must share a clock or otherwise send a clock signal. If the clock phases drift apart, the demodulated I and Q signals bleed into each other, yielding crosstalk. In this context, the clock signal is called a "phase reference". Clock synchronization is typically achieved by transmitting a burst subcarrier or a pilot signal. The phase reference for NTSC, for example, is included within its colorburst signal.

Analog QAM is used in:

• NTSC and PAL analog color television systems, where the I- and Q-signals carry the components of chroma (colour) information. The QAM carrier phase is recovered from a special colorburst transmitted at the beginning of each scan line.
• C-QUAM ("Compatible QAM") is used in AM stereo radio to carry the stereo difference information.

Fourier analysis

Applying Euler's formula to the sinusoids in Eq.1, the positive-frequency portion of s_c (or analytic representation) is:

$s_{c}(t)_{+}={\tfrac {1}{2}}e^{i2\pi f_{c}t}[I(t)+iQ(t)]\quad {\stackrel {\mathcal {F}}{\Longrightarrow }}\quad {\tfrac {1}{2}}\left[{\widehat {I\ }}(f-f_{c})+e^{i\pi /2}{\widehat {Q}}(f-f_{c})\right],$

where ${\mathcal {F}}$ denotes the Fourier transform, and ︿I and ︿Q are the transforms of I(t) and Q(t). This result represents the sum of two DSB-SC signals with the same center frequency. The factor of i (= e^iπ/2) represents the 90° phase shift that enables their individual demodulations.

Digital QAM

Digital 16-QAM with example symbols

Constellation points for 4-QAM, 16-QAM, 32-QAM, and 64-QAM overlapped

As in many digital modulation schemes, the constellation diagram is useful for QAM. In QAM, the constellation points are usually arranged in a square grid with equal vertical and horizontal spacing, although other configurations are possible (e.g. a hexagonal or triangular grid). In digital telecommunications the data is usually binary, so the number of points in the grid is typically a power of 2 (2, 4, 8, …), corresponding to the number of bits per symbol. The simplest and most commonly used QAM constellations consist of points arranged in a square, i.e. 16-QAM, 64-QAM and 256-QAM (even powers of two). Non-square constellations, such as Cross-QAM, can offer greater efficiency but are rarely used because of the cost of increased modem complexity.

By moving to a higher-order constellation, it is possible to transmit more bits per symbol. However, if the mean energy of the constellation is to remain the same (by way of making a fair comparison), the points must be closer together and are thus more susceptible to noise and other corruption; this results in a higher bit error rate and so higher-order QAM can deliver more data less reliably than lower-order QAM, for constant mean constellation energy. Using higher-order QAM without increasing the bit error rate requires a higher signal-to-noise ratio (SNR) by increasing signal energy, reducing noise, or both.

If data rates beyond those offered by 8-PSK are required, it is more usual to move to QAM since it achieves a greater distance between adjacent points in the I-Q plane by distributing the points more evenly. The complicating factor is that the points are no longer all the same amplitude and so the demodulator must now correctly detect both phase and amplitude, rather than just phase.

64-QAM and 256-QAM are often used in digital cable television and cable modem applications. In the United States, 64-QAM and 256-QAM are the mandated modulation schemes for digital cable (see QAM tuner) as standardised by the SCTE in the standard ANSI/SCTE 07 2013. In the UK, 64-QAM is used for digital terrestrial television (Freeview) whilst 256-QAM is used for Freeview-HD.

Bit-loading (bits per QAM constellation) on an ADSL line

Communication systems designed to achieve very high levels of spectral efficiency usually employ very dense QAM constellations. For example, current Homeplug AV2 500-Mbit/s powerline Ethernet devices use 1024-QAM and 4096-QAM, as well as future devices using ITU-T G.hn standard for networking over existing home wiring (coaxial cable, phone lines and power lines); 4096-QAM provides 12 bits/symbol. Another example is ADSL technology for copper twisted pairs, whose constellation size goes up to 32768-QAM (in ADSL terminology this is referred to as bit-loading, or bit per tone, 32768-QAM being equivalent to 15 bits per tone).

Ultra-high capacity microwave backhaul systems also use 1024-QAM. With 1024-QAM, adaptive coding and modulation (ACM) and XPIC, vendors can obtain gigabit capacity in a single 56 MHz channel.

Interference and noise

In moving to a higher order QAM constellation (higher data rate and mode) in hostile RF/microwave QAM application environments, such as in broadcasting or telecommunications, multipath interference typically increases. There is a spreading of the spots in the constellation, decreasing the separation between adjacent states, making it difficult for the receiver to decode the signal appropriately. In other words, there is reduced noise immunity. There are several test parameter measurements which help determine an optimal QAM mode for a specific operating environment. The following three are most significant:

• Carrier/interference ratio
• Carrier-to-noise ratio
• Threshold-to-noise ratio

See also

• Amplitude and phase-shift keying or asymmetric phase-shift keying (APSK)
• Carrierless amplitude phase modulation (CAP)
• Circle packing § Applications
• In-phase and quadrature components
• Modulation for other examples of modulation techniques
• Phase-shift keying
• QAM tuner for HDTV
• Random modulation

Further reading

• Jonqyin (Russell) Sun "Linear diversity analysis for QAM in Rician fading channels", IEEE WOCC 2014
• John G. Proakis, "Digital Communications, 3rd Edition"

External links

• QAM Demodulation
• Interactive webdemo of QAM constellation with additive noise Institute of Telecommunicatons, University of Stuttgart
• QAM bit error rate for AWGN channel – online experiment
• How imperfections affect QAM constellation
• Microwave Phase Shifters Overview by Herley General Microwave
• Simulation of dual-polarization QPSK (DP-QPSK) for 100G optical transmission

Single-Carrier FDMA (SC-FDE)

Single-carrier FDMA (SC-FDMA) is a frequency-division multiple access scheme. Originally known as Carrier Interferometry, it is also called linearly precoded OFDMA (LP-OFDMA). Like other multiple access schemes (TDMA, FDMA, CDMA, OFDMA), it deals with the assignment of multiple users to a shared communication resource. SC-FDMA can be interpreted as a linearly precoded OFDMA scheme, in the sense that it has an additional DFT processing step preceding the conventional OFDMA processing.

SC-FDMA has drawn great attention as an attractive alternative to OFDMA, especially in the uplink communications where lower peak-to-average power ratio (PAPR) greatly benefits the mobile terminal in terms of transmit power efficiency and reduced cost of the power amplifier. This is where SC-FDMA gets its name from: it's an OFDM signal that mimics the characteristics of a single-carrier QAM signal. It has been adopted as the uplink multiple access scheme in 3GPP Long Term Evolution (LTE), or Evolved UTRA (E-UTRA).

The performance of SC-FDMA in relation to OFDMA has been the subject of various studies. Although the performance gap is small, SC-FDMA's advantage of low PAPR makes it desirable for uplink wireless transmission in mobile communication systems, where transmitter power efficiency is of paramount importance.

Transmitter and receiver structure

The transmission processing of SC-FDMA is very similar to that of OFDMA. For each user, the sequence of bits transmitted is mapped to a complex constellation of symbols (BPSK, QPSK, or M-QAM). Then different transmitters (users) are assigned different Fourier coefficients. This assignment is carried out in the mapping and demapping blocks. The receiver side includes one demapping block, one IDFT block, and one detection block for each user signal to be received. Just like in OFDM, guard intervals (called cyclic prefixes) with cyclic repetition are introduced between blocks of symbols in view to efficiently eliminate inter-symbol interference from time spreading (caused by multi-path propagation) among the blocks.

In SC-FDMA, multiple access among users is made possible by assigning different users different sets of non-overlapping Fourier coefficients (sub-carriers). This is achieved at the transmitter by inserting (prior to IDFT) silent Fourier coefficients (at positions assigned to other users), and removing them on the receiver side after the DFT.

Localized and distributed mapping

The distinguishing feature of SC-FDMA is that it leads to a single-carrier transmit signal, in contrast to OFDMA which is a multi-carrier transmission scheme. Subcarrier mapping can be classified into two types: localized mapping and distributed mapping. In localized mapping, the DFT outputs are mapped to a subset of consecutive subcarriers, thereby confining them to only a fraction of the system bandwidth. In distributed mapping, the DFT outputs of the input data are assigned to subcarriers over the entire bandwidth non-continuously, resulting in zero amplitude for the remaining subcarriers. A special case of distributed SC-FDMA is called interleaved SC-FDMA (IFDMA), where the occupied subcarriers are equally spaced over the entire bandwidth.

Owing to its inherent single carrier structure, a prominent advantage of SC-FDMA over OFDM and OFDMA is that its transmit signal has a lower peak-to-average power ratio (PAPR), resulting in relaxed design parameters in the transmit path of a subscriber unit. Intuitively, the reason lies in the fact that where OFDM transmit symbols directly modulate multiple sub-carriers, SC-FDMA transmit symbols are first processed by an N-point DFT block.

In OFDM, as well as SC-FDMA, equalization is achieved on the receiver side, after the DFT calculation, by multiplying each Fourier coefficient by a complex number. Thus, frequency-selective fading and phase distortion can be easily counteracted. The advantage is that frequency domain equalization using FFTs requires less computation than conventional time-domain equalization, which require multi-tap FIR or IIR-filters. Less computations result in less compounded round-off error, which can be viewed as numerical noise.

A related concept is the combination of a single carrier transmission with the single-carrier frequency-domain-equalization (SC-FDE) scheme. The single carrier transmission, unlike SC-FDMA and OFDM, employs no IDFT or DFT at the transmitter, but introduces the cyclic prefix to transform the linear channel convolution into a circular one. After removing the cyclic prefix at the receiver, a DFT is applied to arrive in the frequency domain, where a simple single-carrier frequency-domain-equalization (SC-FDE) scheme can be employed, followed by the IDFT operation.

• DFT: Discrete Fourier Transform
• IDFT: Inverse Discrete Fourier Transform
• CP: Cyclic Prefix
• PS: Pulse Shaping
• DAC: Digital-to-analog converter
• RF: Radio Frequency signal
• ADC: Analog-to-digital converter
• LP-OFDMA: Linearly precoded OFDMA

Useful properties

1. Low PAPR (crest factor)
2. Low sensitivity to carrier frequency offset
3. Less sensitive to non-linear distortion and hence, it allows the use of low-cost power amplifiers
4. Greater robustness against spectral nulls

See also

• Carrier interferometry
• 3GPP Long Term Evolution
• OFDMA
• Time-division multiple access

Trellis Coded Modulation (TCM)

Trellis Coded Modulation

Wavelet Modulation (WDM)

Wavelet Modulation

Hierarchical Modulation

Hierarchical modulation, also called layered modulation, is one of the signal processing techniques for multiplexing and modulating multiple data streams into one single symbol stream, where base-layer symbols and enhancement-layer symbols are synchronously overlaid before transmission.

Hierarchical modulation is particularly used to mitigate the cliff effect in digital television broadcast, particularly mobile TV, by providing a (lower quality) fallback signal in case of weak signals, allowing graceful degradation instead of complete signal loss. It has been widely proven and included in various standards, such as DVB-T, MediaFLO, UMB (Ultra Mobile Broadband, a new 3.5th generation mobile network standard developed by 3GPP2), and is under study for DVB-H.

Hierarchical modulation is also taken as one of the practical implementations of superposition precoding, which can help achieve the maximum sum rate of broadcast channels. When hierarchical-modulated signals are transmitted, users with good reception and advanced receivers can demodulate multiple layers. For a user with a conventional receiver or poor reception, it may only demodulate the data stream embedded in the base layer. With hierarchical modulation, a network operator can target users of different types with different services or QoS.

However, traditional hierarchical modulation suffers from serious inter-layer interference (ILI) with impact on the achievable symbol rate.

Example

Layered modulation constellation:

• ● 2 bits, QPSK
• ■ 4 bits, 64QAM

For example, the figure depicts a layering scheme with QPSK base layer, and a 64QAM enhancement layer. The first layer is 2 bits (represented by the green circles). The signal detector only needs to establish which quadrant the signal is in, to recover the value (which is '10', the green circle in the lower right corner). In better signal conditions, the detector can establish the phase and amplitude more precisely, to recover four more bits of data ('1101'). Thus, the base layer carries '10', and the enhancement layer carries '1101'.

Inter-layer interference

For a hierarchically-modulated symbol with QPSK base layer and 16QAM enhancement layer, the base-layer throughput loss is up to about 1.5 bits/symbol with the total receive signal-to-noise ratio (SNR) at about 23 dB, about the minimum needed for the comparable non-hierarchical modulation, 64QAM. But unlayered 16QAM with the same SNR would approach full throughput. This means, due to ILI, about 1.5/4 = 37.5% loss of the base-layer achievable throughput. Furthermore, due to ILI and the imperfect demodulation of base-layer symbols, the demodulation error rate of higher-layer symbols increases too.

See also

• Link adaptation
• H.264 Scalable Video Coding
• H.265 scalability extensions (SHVC)
• AV1 Scalable video coding
• MPEG-4 SLS
• MPEG-5 Part 2 / Low Complexity Enhancement Video Coding / LC EVC
• DTS-HD MA
• Ogg Vorbis bitrate peeling
• WavPack hybrid mode
• JPEG 2000 SNR scalability

References

• H. Méric, J. Lacan, F. Arnal, G. Lesthievent, M.-L. Boucheret, Combining Adaptive Coding and Modulation With Hierarchical Modulation in Satcom Systems, IEEE Transactions on Broadcasting, Vol. 59, No. 4 (2013), pp 627-637.
• Shu Wang, Soonyil Kwon and Yi, B.K., On enhancing hierarchical modulation, IEEE International Symposium on Broadband Multimedia Systems and Broadcasting, March 31 2008-April 2 2008, Las Vegas, NV, (2008), pp. 1-6.
• Seamus O Leary, 'Hierarchical transmission and COFDM systems', Published in: IEEE Transactions on Broadcasting ( Volume: 43, Issue: 2, Jun 1997)Page(s): 166 - 174

External links

• Hierarchical Modulation Explained at the Wayback Machine (archived 2012-03-25)
• Hierarchical Modulation under DVB

Chirp Spread Spectrum (CSS)

A linear frequency modulated upchirp in the time domain. Other types of upchirps may increase exponentially over time.

In digital communications, chirp spread spectrum (CSS) is a spread spectrum technique that uses wideband linear frequency modulated chirp pulses to encode information. A chirp is a sinusoidal signal whose frequency increases or decreases over time (often with a polynomial expression for the relationship between time and frequency).

Overview

As with other spread spectrum methods, chirp spread spectrum uses its entire allocated bandwidth to broadcast a signal, making it robust to channel noise. Further, because the chirps utilize a broad band of the spectrum, chirp spread spectrum is also resistant to multi-path fading even when operating at very low power. However, it is unlike direct-sequence spread spectrum (DSSS) or frequency-hopping spread spectrum (FHSS) in that it does not add any pseudo-random elements to the signal to help distinguish it from noise on the channel, instead relying on the linear nature of the chirp pulse. Additionally, chirp spread spectrum is resistant to the Doppler effect, which is typical in mobile radio applications.

Uses

Chirp spread spectrum was originally designed to compete with ultra-wideband for precision ranging and low-rate wireless networks in the 2.45 GHz band. However, since the release of IEEE 802.15.4a (also known as IEEE 802.15.4a-2007), it is no longer actively being considered by the IEEE for standardization in the area of precision ranging.

Chirp spread spectrum is ideal for applications requiring low power usage and needing relatively low data rates (1 Mbit/s or less). In particular, IEEE 802.15.4a specifies CSS as a technique for use in low-rate wireless personal area networks (LR-WPAN). However, whereas IEEE 802.15.4-2006 standard specifies that WPANs encompass an area of 10 m or less, IEEE 802.15.4a-2007, specifies CSS as a physical layer to be used when longer ranges and devices moving at high speeds are part of your network. Nanotron's CSS implementation was actually seen to work at a range of 570 meters between devices. Further, Nanotron's implementation can work at data rates of up to 2 Mbit/s - higher than specified in 802.15.4a. Finally, the IEEE 802.15.4a PHY standard actually mixes CSS encoding techniques with differential phase shift keying modulation (DPSK) to achieve better data rates.

Chirp spread spectrum may also be used in the future for military applications as it is very difficult to detect and intercept when operating at low power.

Very similar frequency swept waveforms are used in frequency modulated continuous wave radars to measure range (distance); an unmodulated continuous wave Doppler radar can only measure range-rate (relative velocity along the line of sight). FM-CW radars are very widely used as radio altimeters in aircraft.

One application of chirp spread spectrum is LoRa.

See also

• Bluetooth
• IEEE 802.11
• IEEE 802.15.4
• IEEE 802.15.4a
• IEEE 802.16
• IEEE 802.20
• IEEE 802.22
• Spectral efficiency comparison table
• Zigbee

External links

• Download the 802.15 standards from IEEE
• IEEE 802.15 WPAN Low Rate Alternative PHY Task Group 4a (TG4a)
• Nanotron Technologies Frequently asked Questions page
• Nanotron Chirp Spread Spectrum page
• Nanotron nanoNET Chirp Based Wireless Networks
• About coexistence of IEEE 802.15.4aCSS with IEEE 802.11b/g (2.45 GHz WLAN)

Direct-Sequence Spread Spectrum (DSSS)

In telecommunications, direct-sequence spread spectrum (DSSS) is a spread-spectrum modulation technique primarily used to reduce overall signal interference. The direct-sequence modulation makes the transmitted signal wider in bandwidth than the information bandwidth. After the despreading or removal of the direct-sequence modulation in the receiver, the information bandwidth is restored, while the unintentional and intentional interference is substantially reduced.

Swiss inventor, Gustav Guanella proposed a "means for and method of secret signals". With DSSS, the message symbols are modulated by a sequence of complex values known as spreading sequence. Each element of the spreading sequence, a so-called chip, has a shorter duration than the original message symbols. The modulation of the message symbols scrambles and spreads the signal in the spectrum, and thereby results in a bandwidth of the spreading sequence. The smaller the chip duration, the larger the bandwidth of the resulting DSSS signal; more bandwidth multiplexed to the message signal results in better resistance against narrowband interference.

Some practical and effective uses of DSSS include the code-division multiple access (CDMA) method, the IEEE 802.11b specification used in Wi-Fi networks, and the Global Positioning System.

Transmission method

Direct-sequence spread-spectrum transmissions multiply the symbol sequence being transmitted with a spreading sequence that has a higher rate than the original message rate. Usually, sequences are chosen such that the resulting spectrum is spectrally white. Knowledge of the same sequence is used to reconstruct the original data at the receiving end. This is commonly implemented by the element-wise multiplication with the spreading sequence, followed by summation over a message symbol period. This process, despreading, is mathematically a correlation of the transmitted spreading sequence with the spreading sequence. In an AWGN channel, the despreaded signal's signal-to-noise ratio is increased by the spreading factor, which is the ratio of the spreading-sequence rate to the data rate.

While a transmitted DSSS signal occupies a wider bandwidth than the direct modulation of the original signal would require, its spectrum can be restricted by conventional pulse-shape filtering.

If an undesired transmitter transmits on the same channel but with a different spreading sequence, the despreading process reduces the power of that signal. This effect is the basis for the code-division multiple access (CDMA) method of multi-user medium access, which allows multiple transmitters to share the same channel within the limits of the cross-correlation properties of their spreading sequences.

Benefits

• Resistance to unintended or intended jamming
• Sharing of a single channel among multiple users
• Reduced signal/background-noise level hampers interception
• Determination of relative timing between transmitter and receiver

Uses

• The United States GPS, European Galileo and Russian GLONASS satellite navigation systems; earlier GLONASS used DSSS with a single spreading sequence in conjunction with FDMA, while later GLONASS used DSSS to achieve CDMA with multiple spreading sequences.
• DS-CDMA (Direct-Sequence Code Division Multiple Access) is a multiple access scheme based on DSSS, by spreading the signals from/to different users with different codes. It is the most widely used type of CDMA.
• Cordless phones operating in the 900 MHz, 2.4 GHz and 5.8 GHz bands
• IEEE 802.11b 2.4 GHz Wi-Fi, and its predecessor 802.11-1999. (Their successor 802.11g uses both OFDM and DSSS)
• Automatic meter reading
• IEEE 802.15.4 (used, e.g., as PHY and MAC layer for Zigbee, or, as the physical layer for WirelessHART)
• Radio-controlled model Automotive, Aeronautical and Marine vehicles
• Spread spectrum radar for covertness and resistance to jamming and spoofing

See also

• Complementary code keying
• Frequency-hopping spread spectrum
• Linear-feedback shift register
• Orthogonal frequency-division multiplexing

References

• The Origins of Spread-Spectrum Communications
•  This article incorporates public domain material from Federal Standard 1037C. General Services Administration. Archived from the original on 2022-01-22.
• NTIA Manual of Regulations and Procedures for Federal Radio Frequency Management

External links

• Civil Spread Spectrum History

Frequency-Hopping Spread Spectrum (FHSS)

Frequency-Hopping Spread Spectrum

Time-Hopping (THSS)

Time-Hopping

Demodulation

Demodulation is extracting the original information-bearing signal from a carrier wave. A demodulator is an electronic circuit (or computer program in a software-defined radio) that is used to recover the information content from the modulated carrier wave. There are many types of modulation so there are many types of demodulators. The signal output from a demodulator may represent sound (an analog audio signal), images (an analog video signal) or binary data (a digital signal).

These terms are traditionally used in connection with radio receivers, but many other systems use many kinds of demodulators. For example, in a modem, which is a contraction of the terms modulator/demodulator, a demodulator is used to extract a serial digital data stream from a carrier signal which is used to carry it through a telephone line, coaxial cable, or optical fiber.

History

Demodulation was first used in radio receivers. In the wireless telegraphy radio systems used during the first 3 decades of radio (1884–1914) the transmitter did not communicate audio (sound) but transmitted information in the form of pulses of radio waves that represented text messages in Morse code. Therefore, the receiver merely had to detect the presence or absence of the radio signal, and produce a click sound. The device that did this was called a detector. The first detectors were coherers, simple devices that acted as a switch. The term detector stuck, was used for other types of demodulators and continues to be used to the present day for a demodulator in a radio receiver.

The first type of modulation used to transmit sound over radio waves was amplitude modulation (AM), invented by Reginald Fessenden around 1900. An AM radio signal can be demodulated by rectifying it to remove one side of the carrier, and then filtering to remove the radio-frequency component, leaving only the modulating audio component. This is equivalent to peak detection with a suitably long time constant. The amplitude of the recovered audio frequency varies with the modulating audio signal, so it can drive an earphone or an audio amplifier. Fessendon invented the first AM demodulator in 1904 called the electrolytic detector, consisting of a short needle dipping into a cup of dilute acid. The same year John Ambrose Fleming invented the Fleming valve or thermionic diode which could also rectify an AM signal.

Techniques

There are several ways of demodulation depending on how parameters of the base-band signal such as amplitude, frequency or phase are transmitted in the carrier signal. For example, for a signal modulated with a linear modulation like AM (amplitude modulation), we can use a synchronous detector. On the other hand, for a signal modulated with an angular modulation, we must use an FM (frequency modulation) demodulator or a PM (phase modulation) demodulator. Different kinds of circuits perform these functions.

Many techniques such as carrier recovery, clock recovery, bit slip, frame synchronization, rake receiver, pulse compression, Received Signal Strength Indication, error detection and correction, etc., are only performed by demodulators, although any specific demodulator may perform only some or none of these techniques.

Many things can act as a demodulator, if they pass the radio waves on nonlinearly.

AM radio

An AM signal encodes the information into the carrier wave by varying its amplitude in direct sympathy with the analogue signal to be sent. There are two methods used to demodulate AM signals:

• The envelope detector is a very simple method of demodulation that does not require a coherent demodulator. It consists of a rectifier (anything that will pass current in one direction only) or other non-linear component that enhances one half of the received signal over the other and a low-pass filter. The rectifier may be in the form of a single diode or may be more complex. Many natural substances exhibit this rectification behaviour, which is why it was the earliest modulation and demodulation technique used in radio. The filter is usually an RC low-pass type but the filter function can sometimes be achieved by relying on the limited frequency response of the circuitry following the rectifier. The crystal set exploits the simplicity of AM modulation to produce a receiver with very few parts, using the crystal as the rectifier and the limited frequency response of the headphones as the filter.
• The product detector multiplies the incoming signal by the signal of a local oscillator with the same frequency and phase as the carrier of the incoming signal. After filtering, the original audio signal will result.

SSB is a form of AM in which the carrier is reduced or suppressed entirely, which require coherent demodulation. For further reading, see sideband.

FM radio

Example of QPSK carrier recovery phase error causing a fixed rotational offset of the received symbol constellation, X, relative to the intended constellation, O.

Frequency modulation (FM) has numerous advantages over AM such as better fidelity and noise immunity. However, it is much more complex to both modulate and demodulate a carrier wave with FM, and AM predates it by several decades.

There are several common types of FM demodulators:

• The quadrature detector, which phase shifts the signal by 90 degrees and multiplies it with the unshifted version. One of the terms that drops out from this operation is the original information signal, which is selected and amplified.
• The signal is fed into a PLL and the error signal is used as the demodulated signal.
• The most common is a Foster–Seeley discriminator. This is composed of an electronic filter which decreases the amplitude of some frequencies relative to others, followed by an AM demodulator. If the filter response changes linearly with frequency, the final analog output will be proportional to the input frequency, as desired.
• A variant of the Foster–Seeley discriminator called the ratio detector
• Another method uses two AM demodulators, one tuned to the high end of the band and the other to the low end, and feed the outputs into a difference amplifier.
• Using a digital signal processor, as used in software-defined radio.

PM

Main article: Phase modulation

Receiver structure for QPSK. The matched filters can be replaced with correlators. Each detection device uses a reference threshold value to determine whether a 1 or 0 is detected.

QAM

Main article: Quadrature amplitude modulation § Demodulation

QAM demodulation requires a coherent receiver. It uses two product detectors whose local reference signals are a quarter cycle apart in phase: one for the in-phase component and one for the quadrature component. The demodulator keeps these product detectors tuned to a continuous or intermittent pilot signal.

See also

• Detection theory
• Detector (radio)
• Fax demodulator

External links

• Demodulation chapter on All About Circuits

Line Coding

An example of coding a binary signal using rectangular pulse-amplitude modulation with polar non-return-to-zero code

An example of bipolar encoding, or AMI.

Encoding of 11011000100 in Manchester encoding

An example of differential Manchester encoding

An example of biphase mark code

An example of MLT-3 encoding

In telecommunications, a line code is a pattern of voltage, current, or photons used to represent digital data transmitted down a communication channel or written to a storage medium. This repertoire of signals is usually called a constrained code in data storage systems. Some signals are more prone to error than others as the physics of the communication channel or storage medium constrains the repertoire of signals that can be used reliably.

Common line encodings are unipolar, polar, bipolar, and Manchester code.

Transmission and storage

After line coding, the signal is put through a physical communication channel, either a transmission medium or data storage medium. The most common physical channels are:

• the line-coded signal can directly be put on a transmission line, in the form of variations of the voltage or current (often using differential signaling).
• the line-coded signal (the baseband signal) undergoes further pulse shaping (to reduce its frequency bandwidth) and then is modulated (to shift its frequency) to create an RF signal that can be sent through free space.
• the line-coded signal can be used to turn on and off a light source in free-space optical communication, most commonly used in an infrared remote control.
• the line-coded signal can be printed on paper to create a bar code.
• the line-coded signal can be converted to magnetized spots on a hard drive or tape drive.
• the line-coded signal can be converted to pits on an optical disc.

Some of the more common binary line codes include:

Signal	Comments	1 state	0 state
NRZ–L	Non-return-to-zero level. This is the standard positive logic signal format used in digital circuits.	forces a high level	forces a low level
NRZ–M	Non-return-to-zero mark	forces a transition	does nothing (keeps sending the previous level)
NRZ–S	Non-return-to-zero space	does nothing (keeps sending the previous level)	forces a transition
RZ	Return to zero	goes high for half the bit period and returns to low	stays low for the entire period
Biphase–L	Manchester. Two consecutive bits of the same type force a transition at the beginning of a bit period.	forces a negative transition in the middle of the bit	forces a positive transition in the middle of the bit
Biphase–M	Variant of Differential Manchester. There is always a transition halfway between the conditioned transitions.	forces a transition	keeps level constant
Biphase–S	Differential Manchester used in Token Ring. There is always a transition halfway between the conditioned transitions.	keeps level constant	forces a transition
Differential Manchester (Alternative)	Need a Clock, always a transition in the middle of the clock period	is represented by no transition.	is represented by a transition at the beginning of the clock period.
Bipolar	The positive and negative pulses alternate.	forces a positive or negative pulse for half the bit period	keeps a zero level during bit period

An arbitrary bit pattern in various binary line code formats

Each line code has advantages and disadvantages. Line codes are chosen to meet one or more of the following criteria:

• Minimize transmission hardware
• Facilitate synchronization
• Ease error detection and correction
• Achieve a target spectral density
• Eliminate a DC component

Disparity

Most long-distance communication channels cannot reliably transport a DC component. The DC component is also called the disparity, the bias, or the DC coefficient. The disparity of a bit pattern is the difference in the number of one bits vs the number of zero bits. The running disparity is the running total of the disparity of all previously transmitted bits. The simplest possible line code, unipolar, gives too many errors on such systems, because it has an unbounded DC component.

Most line codes eliminate the DC component – such codes are called DC-balanced, zero-DC, or DC-free. There are three ways of eliminating the DC component:

• Use a constant-weight code. Each transmitted code word in a constant-weight code is designed such that every code word that contains some positive or negative levels also contains enough of the opposite levels, such that the average level over each code word is zero. Examples of constant-weight codes include Manchester code and Interleaved 2 of 5.
• Use a paired disparity code. Each code word in a paired disparity code that averages to a negative level is paired with another code word that averages to a positive level. The transmitter keeps track of the running DC buildup, and picks the code word that pushes the DC level back towards zero. The receiver is designed so that either code word of the pair decodes to the same data bits. Examples of paired disparity codes include alternate mark inversion, 8b/10b and 4B3T.
• Use a scrambler. For example, the scrambler specified in RFC 2615 for 64b/66b encoding.

Polarity

Bipolar line codes have two polarities, are generally implemented as RZ, and have a radix of three since there are three distinct output levels (negative, positive and zero). One of the principle advantages of this type of code is that it can eliminate any DC component. This is important if the signal must pass through a transformer or a long transmission line.

Unfortunately, several long-distance communication channels have polarity ambiguity. Polarity-insensitive line codes compensate in these channels. There are three ways of providing unambiguous reception of 0 and 1 bits over such channels:

• Pair each code word with the polarity-inverse of that code word. The receiver is designed so that either code word of the pair decodes to the same data bits. Examples include alternate mark inversion, Differential Manchester encoding, coded mark inversion and Miller encoding.
• differential coding each symbol relative to the previous symbol. Examples include MLT-3 encoding and NRZI.
• Invert the whole stream when inverted syncwords are detected, perhaps using polarity switching

Run-length limited codes

For reliable clock recovery at the receiver, a run-length limitation may be imposed on the generated channel sequence, i.e., the maximum number of consecutive ones or zeros is bounded to a reasonable number. A clock period is recovered by observing transitions in the received sequence, so that a maximum run length guarantees sufficient transitions to assure clock recovery quality.

RLL codes are defined by four main parameters: m, n, d, k. The first two, m/n, refer to the rate of the code, while the remaining two specify the minimal d and maximal k number of zeroes between consecutive ones. This is used in both telecommunications and storage systems that move a medium past a fixed recording head.

Specifically, RLL bounds the length of stretches (runs) of repeated bits during which the signal does not change. If the runs are too long, clock recovery is difficult; if they are too short, the high frequencies might be attenuated by the communications channel. By modulating the data, RLL reduces the timing uncertainty in decoding the stored data, which would lead to the possible erroneous insertion or removal of bits when reading the data back. This mechanism ensures that the boundaries between bits can always be accurately found (preventing bit slip), while efficiently using the media to reliably store the maximal amount of data in a given space.

Early disk drives used very simple encoding schemes, such as RLL (0,1) FM code, followed by RLL (1,3) MFM code which were widely used in hard disk drives until the mid-1980s and are still used in digital optical discs such as CD, DVD, MD, Hi-MD and Blu-ray using EFM and EFMPLus codes. Higher density RLL (2,7) and RLL (1,7) codes became the de facto standards for hard disks by the early 1990s.

Synchronization

Main article: Clock recovery

Line coding should make it possible for the receiver to synchronize itself to the phase of the received signal. If the clock recovery is not ideal, then the signal to be decoded will not be sampled at the optimal times. This will increase the probability of error in the received data.

Biphase line codes require at least one transition per bit time. This makes it easier to synchronize the transceivers and detect errors, however, the baud rate is greater than that of NRZ codes.

Other considerations

A line code will typically reflect technical requirements of the transmission medium, such as optical fiber or shielded twisted pair. These requirements are unique for each medium, because each one has different behavior related to interference, distortion, capacitance and attenuation.

Common line codes

• 2B1Q
• 4B3T
• 4B5B
• 6b/8b encoding
• 8b/10b encoding
• 64b/66b encoding
• 128b/130b encoding
• Alternate mark inversion (AMI)
• Coded mark inversion (CMI)
• EFMPlus, used in DVDs
• Eight-to-fourteen modulation (EFM), used in compact discs
• Hamming code
• Hybrid ternary code
• Manchester code and differential Manchester
• Mark and space
• MLT-3 encoding
• Modified AMI codes: B8ZS, B6ZS, B3ZS, HDB3
• Modified frequency modulation, Miller encoding and delay encoding
• Non-return-to-zero (NRZ)
• Non-return-to-zero, inverted (NRZI)
• Pulse-position modulation (PPM)
• Return-to-zero (RZ)
• TC-PAM

Optical line codes

• Alternate-Phase Return-to-Zero (APRZ)
• Carrier-Suppressed Return-to-Zero (CSRZ)
• Three of Six, Fiber Optical (TS-FO)

See also

• Physical layer
• Self-synchronizing code and bit synchronization

References

•  This article incorporates public domain material from Federal Standard 1037C. General Services Administration. Archived from the original on 2022-01-22. (in support of MIL-STD-188).

External links

• Line Coding Lecture No. 9
• Line Coding in Digital Communication
• CodSim 2.0: Open source simulator for Digital Data Communications Model at the University of Malaga written in HTML

Modem

"Computer modem" redirects here. Not to be confused with Computer Modern.

For the French political party known as Modem, see Democratic Movement (France). For the ancient Hebrew city, see Modi'in-Maccabim-Re'ut.

Acoustic coupler modems used a telephone handset as the audio medium, with the user dialing the desired number and then pressing the handset into the modem to complete the connection. These systems generally operated at a speed of 300 bits per second.

A modulator-demodulator or most commonly referred to as modem is a computer hardware device that converts data from a digital format into a format suitable for an analog transmission medium such as telephone or radio. A modem transmits data by modulating one or more carrier wave signals to encode digital information, while the receiver demodulates the signal to recreate the original digital information. The goal is to produce a signal that can be transmitted easily and decoded reliably. Modems can be used with almost any means of transmitting analog signals, from light-emitting diodes to radio.

Early modems were devices that used audible sounds suitable for transmission over traditional telephone systems and leased lines. These generally operated at 110 or 300 bits per second (bit/s), and the connection between devices was normally manual, using an attached telephone handset. By the 1970s, higher speeds of 1,200 and 2,400 bit/s for asynchronous dial connections, 4,800 bit/s for synchronous leased line connections and 35 kbit/s for synchronous conditioned leased lines were available. By the 1980s, less expensive 1,200 and 2,400 bit/s dialup modems were being released, and modems working on radio and other systems were available. As device sophistication grew rapidly in the late 1990s, telephone-based modems quickly exhausted the available bandwidth, reaching 56 kbit/s.

The rise of public use of the internet during the late 1990s led to demands for much higher performance, leading to the move away from audio-based systems to entirely new encodings on cable television lines and short-range signals in subcarriers on telephone lines. The move to cellular telephones, especially in the late 1990s and the emergence of smartphones in the 2000s led to the development of ever-faster radio-based systems. Today, modems are ubiquitous and largely invisible, included in almost every mobile computing device in one form or another, and generally capable of speeds on the order of tens or hundreds of megabytes per second.

Speeds

Modems are frequently classified by the maximum amount of data they can send in a given unit of time, usually expressed in bits per second (symbol bit/s, sometimes abbreviated "bps") or rarely in bytes per second (symbol B/s). Modern broadband modem speeds are typically expressed in megabits per second (Mbit/s).

Historically, modems were often classified by their symbol rate, measured in baud. The baud unit denotes symbols per second, or the number of times per second the modem sends a new signal. For example, the ITU-T V.21 standard used audio frequency-shift keying with two possible frequencies, corresponding to two distinct symbols (or one bit per symbol), to carry 300 bits per second using 300 baud. By contrast, the original ITU-T V.22 standard, which could transmit and receive four distinct symbols (two bits per symbol), transmitted 1,200 bits by sending 600 symbols per second (600 baud) using phase-shift keying.

Many modems are variable-rate, permitting them to be used over a medium with less than ideal characteristics, such as a telephone line that is of poor quality or is too long. This capability is often adaptive so that a modem can discover the maximum practical transmission rate during the connect phase, or during operation.

Collection of modems once used in Australia, including dial-up, DSL, and cable modems

Overall history

Modems grew out of the need to connect teleprinters over ordinary phone lines instead of the more expensive leased lines which had previously been used for current loop–based teleprinters and automated telegraphs. The earliest devices which satisfy the definition of a modem may have been the multiplexers used by news wire services in the 1920s.

In 1941, the Allies developed a voice encryption system called SIGSALY which used a vocoder to digitize speech, then encrypted the speech with one-time pad and encoded the digital data as tones using frequency shift keying. This was also a digital modulation technique, making this an early modem.

Commercial modems largely did not become available until the late 1950s, when the rapid development of computer technology created demand for a method of connecting computers together over long distances, resulting in the Bell Company and then other businesses producing an increasing number of computer modems for use over both switched and leased telephone lines.

Later developments would produce modems that operated over cable television lines, power lines, and various radio technologies, as well as modems that achieved much higher speeds over telephone lines.

Dial-up

A dial-up modem transmits computer data over an ordinary switched telephone line that has not been designed for data use. It was once a widely known technology, mass-marketed globally dial-up internet access. In the 1990s, tens of millions of people in the United States alone used dial-up modems for internet access.

Dial-up service has since been largely superseded by broadband internet, such as DSL.

History

1950s

TeleGuide terminal

Mass production of telephone line modems in the United States began as part of the SAGE air-defense system in 1958, connecting terminals at various airbases, radar sites, and command-and-control centers to the SAGE director centers scattered around the United States and Canada.

Shortly afterwards in 1959, the technology in the SAGE modems was made available commercially as the Bell 101, which provided 110 bit/s speeds. Bell called this and several other early modems "datasets".

1960s

Some early modems were based on touch-tone frequencies, such as Bell 400-style touch-tone modems.

The Bell 103A standard was introduced by AT&T in 1962. It provided full-duplex service at 300 bit/s over normal phone lines. Frequency-shift keying was used, with the call originator transmitting at 1,070 or 1,270 Hz and the answering modem transmitting at 2,025 or 2,225 Hz.

The 103 modem would eventually become a de facto standard once third-party (non-AT&T modems) reached the market, and throughout the 1970s, independently made modems compatible with the Bell 103 de facto standard were commonplace. Example models included the Novation CAT and the Anderson-Jacobson. A lower-cost option was the Pennywhistle modem, designed to be built using readily available parts.

Teletype machines were granted access to remote networks such as the Teletypewriter Exchange using the Bell 103 modem. AT&T also produced reduced-cost units, the originate-only 113D and the answer-only 113B/C modems.

1970s

The 201A Data-Phone was a synchronous modem using two-bit-per-symbol phase-shift keying (PSK) encoding, achieving 2,000 bit/s half-duplex over normal phone lines. In this system the two tones for any one side of the connection are sent at similar frequencies as in the 300 bit/s systems, but slightly out of phase.

In early 1973, Vadic introduced the VA3400 which performed full-duplex at 1,200 bit/s over a normal phone line.

In November 1976, AT&T introduced the 212A modem, similar in design, but using the lower frequency set for transmission. It was not compatible with the VA3400, but it would operate with 103A modem at 300 bit/s.

In 1977, Vadic responded with the VA3467 triple modem, an answer-only modem sold to computer center operators that supported Vadic's 1,200-bit/s mode, AT&T's 212A mode, and 103A operation.

The original 300-baud Hayes Smartmodem

1980s

A significant advance in modems was the Hayes Smartmodem, introduced in 1981. The Smartmodem was an otherwise standard 103A 300 bit/s direct-connect modem, but it introduced a command language which allowed the computer to make control requests, such as commands to dial or answer calls, over the same RS-232 interface used for the data connection. The command set used by this device became a de facto standard, the Hayes command set, which was integrated into devices from many other manufacturers.

Automatic dialing was not a new capability—it had been available via separate Automatic Calling Units, and via modems using the X.21 interface—but the Smartmodem made it available in a single device that could be used with even the most minimal implementations of the ubiquitous RS-232 interface, making this capability accessible from virtually any system or language.

The introduction of the Smartmodem made communications much simpler and more easily accessed. This provided a growing market for other vendors, who licensed the Hayes patents and competed on price or by adding features. This eventually led to legal action over use of the patented Hayes command language.

Dial modems generally remained at 300 and 1,200 bit/s (eventually becoming standards such as V.21 and V.22) into the mid-1980s.

Commodore's 1982 VicModem for the VIC-20 was the first modem to be sold under $100, and the first modem to sell a million units.

In 1984, V.22bis was created, a 2,400-bit/s system similar in concept to the 1,200-bit/s Bell 212. This bit rate increase was achieved by defining four or eight distinct symbols, which allowed the encoding of two or three bits per symbol instead of only one. By the late 1980s, many modems could support improved standards like this, and 2,400-bit/s operation was becoming common.

Increasing modem speed greatly improved the responsiveness of online systems and made file transfer practical. This led to rapid growth of online services with large file libraries, which in turn gave more reason to own a modem. The rapid update of modems led to a similar rapid increase in BBS use.

The introduction of microcomputer systems with internal expansion slots made small internal modems practical. This led to a series of popular modems for the S-100 bus and Apple II computers that could directly dial out, answer incoming calls, and hang up entirely from software, the basic requirements of a bulletin board system (BBS). The seminal CBBS for instance was created on an S-100 machine with a Hayes internal modem, and a number of similar systems followed.

Echo cancellation became a feature of modems in this period, which improved the bandwidth available to both modems by allowing them to ignore their own reflected signals.

Additional improvements were introduced by quadrature amplitude modulation (QAM) encoding, which increased the number of bits per symbol to four through a combination of phase shift and amplitude.

Transmitting at 1,200 baud produced the 4,800 bit/s V.27ter standard, and at 2,400 baud the 9,600 bit/s V.32. The carrier frequency was 1,650 Hz in both systems.

The introduction of these higher-speed systems also led to the development of the digital fax machine during the 1980s. While early fax technology also used modulated signals on a phone line, digital fax used the now-standard digital encoding used by computer modems. This eventually allowed computers to send and receive fax images.

1990s

USRobotics Sportster 14,400 Fax Modem (1994)

In the early 1990s, V.32 modems operating at 9,600 bit/s were introduced, but were expensive and were only starting to enter the market when V.32bis was standardized, which operated at 14,400 bit/s.

Rockwell International's chip division developed a new driver chip set incorporating the V.32bis standard and aggressively priced it. Supra, Inc. arranged a short-term exclusivity arrangement with Rockwell, and developed the SupraFAXModem 14400 based on it. Introduced in January 1992 at $399 (or less), it was half the price of the slower V.32 modems already on the market. This led to a price war, and by the end of the year V.32 was dead, never having been really established, and V.32bis modems were widely available for $250.

V.32bis was so successful that the older high-speed standards had little advantages. USRobotics (USR) fought back with a 16,800 bit/s version of HST, while AT&T introduced a one-off 19,200 bit/s method they referred to as V.32ter, but neither non-standard modem sold well.

V.34 modem implemented as an internal ISA card

V.34 data/fax modem as PC card for notebooks

External V.34 modem with RS-232 serial port

Consumer interest in these proprietary improvements waned during the lengthy introduction of the 28,800 bit/s V.34 standard. While waiting, several companies decided to release hardware and introduced modems they referred to as V.Fast.

In order to guarantee compatibility with V.34 modems once a standard was ratified (1994), manufacturers used more flexible components, generally a DSP and microcontroller, as opposed to purpose-designed ASIC modem chips. This would allow later firmware updates to conform with the standards once ratified.

The ITU standard V.34 represents the culmination of these joint efforts. It employed the most powerful coding techniques available at the time, including channel encoding and shape encoding. From the mere four bits per symbol (9.6 kbit/s), the new standards used the functional equivalent of 6 to 10 bits per symbol, plus increasing baud rates from 2,400 to 3,429, to create 14.4, 28.8, and 33.6 kbit/s modems. This rate is near the theoretical Shannon limit of a phone line.

56 kbit/s technologies

While 56 kbit/s speeds had been available for leased-line modems for some time, they did not become available for dial up modems until the late 1990s.

Dial-up modem bank at an ISP

In the late 1990s, technologies to achieve speeds above 33.6 kbit/s began to be introduced. Several approaches were used, but all of them began as solutions to a single fundamental problem with phone lines.

By the time technology companies began to investigate speeds above 33.6 kbit/s, telephone companies had switched almost entirely to all-digital networks. As soon as a phone line reached a local central office, a line card converted the analog signal from the subscriber to a digital one and conversely. While digitally encoded telephone lines notionally provide the same bandwidth as the analog systems they replaced, the digitization itself placed constraints on the types of waveforms that could be reliably encoded.

The first problem was that the process of analog-to-digital conversion is intrinsically lossy, but second, and more importantly, the digital signals used by the telcos were not "linear": they did not encode all frequencies the same way, instead utilizing a nonlinear encoding (μ-law and a-law) meant to favor the nonlinear response of the human ear to voice signals. This made it very difficult to find a 56 kbit/s encoding that could survive the digitizing process.

Modem manufacturers discovered that, while the analog to digital conversion could not preserve higher speeds, digital-to-analog conversions could. Because it was possible for an ISP to obtain a direct digital connection to a telco, a digital modem – one that connects directly to a digital telephone network interface, such as T1 or PRI – could send a signal that utilized every bit of bandwidth available in the system. While that signal still had to be converted back to analog at the subscriber end, that conversion would not distort the signal in the same way that the opposite direction did.

Early 56k dial-up products

The first 56k (56 kbit/s) dial-up option was a proprietary design from USRobotics, which they called "X2" because 56k was twice the speed (×2) of 28k modems.

At that time, USRobotics held a 40% share of the retail modem market, while Rockwell International held an 80% share of the modem chipset market. Concerned with being shut out, Rockwell began work on a rival 56k technology. They joined with Lucent and Motorola to develop what they called "K56Flex" or just "Flex".

Both technologies reached the market around February 1997; although problems with K56Flex modems were noted in product reviews through July, within six months the two technologies worked equally well, with variations dependent largely on local connection characteristics.

The retail price of these early 56k modems was about US$200, compared to $100 for standard 33k modems. Compatible equipment was also required at the Internet service providers (ISPs) end, with costs varying depending on whether their current equipment could be upgraded. About half of all ISPs offered 56k support by October 1997. Consumer sales were relatively low, which USRobotics and Rockwell attributed to conflicting standards.

Standardized 56k (V.90/V.92)

In February 1998, The International Telecommunication Union (ITU) announced the draft of a new 56 kbit/s standard V.90 with strong industry support. Incompatible with either existing standard, it was an amalgam of both, but was designed to allow both types of modem by a firmware upgrade. The V.90 standard was approved in September 1998 and widely adopted by ISPs and consumers.

The ITU-T V.92 standard was approved by ITU in November 2000 and utilized digital PCM technology to increase the upload speed to a maximum of 48 kbit/s.

The high upload speed was a tradeoff. Use of the 48 kbit/s upstream rate would reduce the downstream as low as 40 kbit/s due to echo effects on the line. To avoid this problem, V.92 modems offer the option to turn off the digital upstream and instead use a plain 33.6 kbit/s analog connection in order to maintain a high digital downstream of 50 kbit/s or higher.

V.92 also added two other features. The first is the ability for users who have call waiting to put their dial-up Internet connection on hold for extended periods of time while they answer a call. The second feature is the ability to quickly connect to one's ISP, achieved by remembering the analog and digital characteristics of the telephone line and using this saved information when reconnecting.

Evolution of dial-up speeds

These values are maximum values, and actual values may be slower under certain conditions (for example, noisy phone lines). For a complete list see the companion article list of device bandwidths. A baud is one symbol per second; each symbol may encode one or more data bits.

Connection	Modulation	Bit rate [kbit/s]	Year released
110 baud Bell 101 modem	FSK	0.1	1958
300 baud (Bell 103 or V.21)	FSK	0.3	1962
1,200 bit/s (1200 baud) (Bell 202)	FSK	1.2	1976
1,200 bit/s (600 baud) (Bell 212A or V.22)	QPSK	1.2	1980
2,000 bit/s (1000 baud) (Bell 201A)	PSK	2.0	1962
2,400 bit/s (600 baud) (V.22bis)	QAM	2.4	1984
2,400 bit/s (1200 baud) (V.26bis)	PSK	2.4
4,800 bit/s (1600 baud) (V.27ter)	PSK	4.8	1976
4,800 bit/s (1600 baud, Bell 208B)	DPSK	4.8
9,600 bit/s (2400 baud) (V.32)	trellis	9.6	1984
14.4 kbit/s (2400 baud) (V.32bis)	trellis	14.4	1991
19.2 kbit/s (2400 baud) (V.32terbo)	trellis	19.2	1993
28.8 kbit/s (3200 baud) (V.34)	trellis	28.8	1994
33.6 kbit/s (3429 baud) (V.34)	trellis	33.6	1996
56 kbit/s (8000/3429 baud) (V.90)	digital	56.0/33.6	1998
56 kbit/s (8000/8000 baud) (V.92)	digital	56.0/48.0	2000
Bonding modem (two 56k modems) (V.92)		112.0/96.0
Hardware compression (variable) (V.90/V.42bis)		56.0–220.0
Hardware compression (variable) (V.92/V.44)		56.0–320.0
Server-side web compression (variable) (Netscape ISP)		100.0–1,000.0

Compression

Many dial-up modems implement standards for data compression to achieve higher effective throughput for the same bitrate. V.44 is an example used in conjunction with V.92 to achieve speeds greater than 56k over ordinary phone lines.

As telephone-based 56k modems began losing popularity, some Internet service providers such as Netzero/Juno, Netscape, and others started using pre-compression to increase apparent throughput. This server-side compression can operate much more efficiently than the on-the-fly compression performed within modems, because the compression techniques are content-specific (JPEG, text, EXE, etc.).The drawback is a loss in quality, as they use lossy compression which causes images to become pixelated and smeared. ISPs employing this approach often advertised it as "accelerated dial-up".

These accelerated downloads are integrated into the Opera and Amazon Silk web browsers, using their own server-side text and image compression requiring all data to pass through their own servers before reaching the user.

Methods of attachment

Dial-up modems can attach in two different ways: with an acoustic coupler, or with a direct electrical connection.

Directly connected modems

The case Hush-A-Phone Corp. v. United States, which legalized acoustic couplers, applied only to mechanical connections to a telephone set, not electrical connections to the telephone line. The Carterfone decision of 1968, however, permitted customers to attach devices directly to a telephone line as long as they followed stringent Bell-defined standards for non-interference with the phone network. This opened the door to independent (non-AT&T) manufacture of direct-connect modems, that plugged directly into the phone line rather than via an acoustic coupler.

While Carterfone required AT&T to permit connection of devices, AT&T successfully argued that they should be allowed to require the use of a special device to protect their network, placed in between the third-party modem and the line, called a Data Access Arrangement or DAA. The use of DAAs was mandatory from 1969 to 1975 when the new FCC Part 68 rules allowed the use of devices without a Bell-provided DAA, subject to equivalent circuitry being included in the third-party device.

Virtually all modems produced after the 1980s are direct-connect.

Acoustic couplers

See also: Acoustic coupler

The Novation CAT acoustically coupled modem

While Bell (AT&T) provided modems that attached via direct wire connection to the phone network as early as 1958, their regulations at the time did not permit the direct electrical connection of any non-Bell device to a telephone line. However, the Hush-a-Phone ruling allowed customers to attach any device to a telephone set as long as it did not interfere with its functionality. This allowed third-party (non-Bell) manufacturers to sell modems utilizing an acoustic coupler.

With an acoustic coupler, an ordinary telephone handset was placed in a cradle containing a speaker and microphone positioned to match up with those on the handset. The tones used by the modem were transmitted and received into the handset, which then relayed them to the phone line.

Because the modem was not electrically connected, it was incapable of picking up, hanging up or dialing, all of which required direct control of the line. Touch-tone dialing would have been possible, but touch-tone was not universally available at this time. Consequently, the dialing process was executed by the user lifting the handset, dialing, then placing the handset on the coupler. To accelerate this process, a user could purchase a dialer or Automatic Calling Unit.

Automatic calling units

Early modems could not place or receive calls on their own, but required human intervention for these steps.

As early as 1964, Bell provided automatic calling units that connected separately to a second serial port on a host machine and could be commanded to open the line, dial a number, and even ensure the far end had successfully connected before transferring control to the modem. Later on, third-party models would become available, sometimes known simply as dialers, and features such as the ability to automatically sign in to time-sharing systems.

Eventually this capability would be built into modems and no longer require a separate device.

Controller-based modems vs. soft modems

Main article: Softmodem

A PCI Winmodem soft modem (on the left) next to a conventional ISA modem (on the right)

Prior to the 1990s, modems contained all the electronics and intelligence to convert data in discrete form to an analog (modulated) signal and back again, and to handle the dialing process, as a mix of discrete logic and special-purpose chips. This type of modem is sometimes referred to as controller-based.

In 1993, Digicom introduced the Connection 96 Plus, a modem which replaced the discrete and custom components with a general purpose digital signal processor, which could be reprogrammed to upgrade to newer standards.

Subsequently, USRobotics released the Sportster Winmodem, a similarly upgradable DSP-based design.

As this design trend spread, both terms – soft modem and Winmodem – obtained a negative connotation in non-Windows-based computing circles because the drivers were either unavailable for non-Windows platforms, or were only available as unmaintainable closed-source binaries, a particular problem for Linux users.

Later in the 1990s, software-based modems became available. These are essentially sound cards, and in fact a common design uses the AC'97 audio codec, which provides multichannel audio to a PC and includes three audio channels for modem signals.

The audio sent and received on the line by a modem of this type is generated and processed entirely in software, often in a device driver. There is little functional difference from the user's perspective, but this design reduces the cost of a modem by moving most of the processing power into inexpensive software instead of expensive hardware DSPs or discrete components.

Soft modems of both types either are internal cards or connect over external buses such as USB. They never utilize RS-232 because they require high bandwidth channels to the host computers to carry the raw audio signals generated (sent) or analyzed (received) by software.

Since the interface is not RS-232, there is no standard for communication with the device directly. Instead, soft modems come with drivers which create an emulated RS-232 port, which standard modem software (such as an operating system dialer application) can communicate with.

Voice/fax modems

"Voice" and "fax" are terms added to describe any dial modem that is capable of recording/playing audio or transmitting/receiving faxes. Some modems are capable of all three functions.

Voice modems are used for computer telephony integration applications as simple as placing/receiving calls directly through a computer with a headset, and as complex as fully automated robocalling systems.

Fax modems can be used for computer-based faxing, in which faxes are sent and received without inbound or outbound faxes ever needing to ever be printed on paper. This differs from efax, in which faxing occurs over the internet, in some cases involving no phone lines whatsoever.

Modem Over IP (Modem Relay)

The ITU-T V.150.1 Recommendation defines procedures for the inter-operation of PSTN to IP gateways. In a classic example of this setup, each dial-up modem would connect to a modem relay gateway. The gateways are then connected to an IP network (such as the Internet). The analog connection from the modem is terminated at the gateway and the signal is demodulated. The demodulated control signals are transported over the IP network in an RTP packet type defined as State Signaling Events (SSEs). The data from the demodulated signal is sent over the IP network via a transport protocol (also defined as an RTP payload) called Simple Packet Relay Transport (SPRT). Both the SSE and SPRT packet formats are defined in the V.150.1 Recommendation (Annex C and Annex B respectively). The gateway at the remote end that receives the packets uses the information to re-modulate the signal for the modem connected at that end.

While the V.150.1 Recommendation is not widely deployed, a pared down version of the recommendation called "Minimum Essential Requirements (MER) for V.150.1 Gateways" (SCIP-216) is used in Secure Telephony applications.

Cloud-based Modems

While traditionally a hardware device, fully software-based modems with the ability to be deployed in a cloud environment (such as Microsoft Azure or AWS) do exist. Leveraging a Voice-over-IP (VoIP) connection through a SIP Trunk, the modulated audio samples are generated and sent over an IP network via RTP and an uncompressed audio codec (such as G.711 μ-law or a-law).

Popularity

A 1994 Software Publishers Association found that although 60% of computers in US households had a modem, only 7% of households went online. A CEA study in 2006 found that dial-up Internet access was declining in the US. In 2000, dial-up Internet connections accounted for 74% of all US residential Internet connections. The United States demographic pattern for dial-up modem users per capita has been more or less mirrored in Canada and Australia for the past 20 years.

Dial-up modem use in the US had dropped to 60% by 2003, and stood at 36% in 2006. Voiceband modems were once the most popular means of Internet access in the US, but with the advent of new ways of accessing the Internet, the traditional 56K modem was losing popularity. The dial-up modem is still widely used by customers in rural areas where DSL, cable, wireless broadband, satellite, or fiber optic service are either not available or they are unwilling to pay what the available broadband companies charge. In its 2012 annual report, AOL showed it still collected around $700 million in fees from about three million dial-up users.

TTY/TDD

TDD devices are a subset of the teleprinter intended for use by the deaf or hard of hearing, essentially a small teletype with a built-in dial-up modem and acoustic coupler. The first models produced in 1964 utilized FSK modulation much like early computer modems.

Leased-line modems

A leased line modem also uses ordinary phone wiring, like dial-up and DSL, but does not use the same network topology. While dial-up uses a normal phone line and connects through the telephone switching system, and DSL uses a normal phone line but connects to equipment at the telco central office, leased lines do not terminate at the telco.

Leased lines are pairs of telephone wire that have been connected together at one or more telco central offices so that they form a continuous circuit between two subscriber locations, such as a business' headquarters and a satellite office. They provide no power or dialtone - they are simply a pair of wires connected at two distant locations.

A dialup modem will not function across this type of line, because it does not provide the power, dialtone and switching that those modems require. However, a modem with leased-line capability can operate over such a line, and in fact can have greater performance because the line is not passing through the telco switching equipment, the signal is not filtered, and therefore greater bandwidth is available.

Leased-line modems can operate in 2-wire or 4-wire mode. The former uses a single pair of wires and can only transmit in one direction at a time, while the latter uses two pairs of wires and can transmit in both directions simultaneously. When two pairs are available, bandwidth can be as high as 1.5 Mbit/s, a full data T1 circuit.

While the slower leased line modems used, e.g., RS-232, interfaces, the faster wideband modems used, e.g., V.35.

Broadband

DSL modem

Cable modem

The term broadband was previously used to describe communications faster than what was available on voice grade channels.

The term broadband gained widespread adoption in the late 1990s to describe internet access technology exceeding the 56 kilobit/s maximum of dialup. There are many broadband technologies, such as various DSL (digital subscriber line) technologies and cable broadband.

DSL technologies such as ADSL, HDSL, and VDSL use telephone lines (wires that were installed by a telephone company and originally intended for use by a telephone subscriber) but do not utilize most of the rest of the telephone system. Their signals are not sent through ordinary phone exchanges, but are instead received by special equipment (a DSLAM) at the telephone company central office.

Because the signal does not pass through the telephone exchange, no "dialing" is required, and the bandwidth constraints of an ordinary voice call are not imposed. This allows much higher frequencies, and therefore much faster speeds. ADSL in particular is designed to permit voice calls and data usage over the same line simultaneously.

Similarly, cable modems use infrastructure originally intended to carry television signals, and like DSL, typically permit receiving television signals at the same time as broadband internet service.

Other broadband modems include FTTx modems, satellite modems, and power line modems.

Terminology

Different terms are used for broadband modems, because they frequently contain more than just a modulation/demodulation component.

Because high-speed connections are frequently used by multiple computers at once, many broadband modems do not have direct (e.g. USB) PC connections. Rather they connect over a network such as Ethernet or Wi-Fi. Early broadband modems offered Ethernet handoff allowing the use of one or more public IP addresses, but no other services such as NAT and DHCP that would allow multiple computers to share one connection. This led to many consumers purchasing separate "broadband routers," placed between the modem and their network, to perform these functions.

Eventually, ISPs began providing residential gateways which combined the modem and broadband router into a single package that provided routing, NAT, security features, and even Wi-Fi access in addition to modem functionality, so that subscribers could connect their entire household without purchasing any extra equipment. Even later, these devices were extended to provide "triple play" features such as telephony and television service. Nonetheless, these devices are still often referred to simply as "modems" by service providers and manufacturers.

Consequently, the terms "modem", "router", and "gateway" are now used interchangeably in casual speech, but in a technical context "modem" may carry a specific connotation of basic functionality with no routing or other features, while the others describe a device with features such as NAT.

Broadband modems may also handle authentication such as PPPoE. While it is often possible to authenticate a broadband connection from a users PC, as was the case with dial-up internet service, moving this task to the broadband modem allows it to establish and maintain the connection itself, which makes sharing access between PCs easier since each one does not have to authenticate separately. Broadband modems typically remain authenticated to the ISP as long as they are powered on.

Radio

A bluetooth radio module with built-in antenna (left)

Any communication technology sending digital data wirelessly involves a modem. This includes direct broadcast satellite, WiFi, WiMax, mobile phones, GPS, Bluetooth and NFC.

Modern telecommunications and data networks also make extensive use of radio modems where long distance data links are required. Such systems are an important part of the PSTN, and are also in common use for high-speed computer network links to outlying areas where fiber optic is not economical.

Wireless modems come in a variety of types, bandwidths, and speeds. Wireless modems are often referred to as transparent or smart. They transmit information that is modulated onto a carrier frequency to allow many wireless communication links to work simultaneously on different frequencies.

Transparent modems operate in a manner similar to their phone line modem cousins. Typically, they were half duplex, meaning that they could not send and receive data at the same time. Typically, transparent modems are polled in a round robin manner to collect small amounts of data from scattered locations that do not have easy access to wired infrastructure. Transparent modems are most commonly used by utility companies for data collection.

Smart modems come with media access controllers inside, which prevents random data from colliding and resends data that is not correctly received. Smart modems typically require more bandwidth than transparent modems, and typically achieve higher data rates. The IEEE 802.11 standard defines a short range modulation scheme that is used on a large scale throughout the world.

Mobile broadband

See also: Mobile broadband and Mobile broadband modem

Huawei HSPA+ (EVDO) USB wireless modem from Movistar Colombia

Huawei 4G+ Dual Band Modem

Modems which use a mobile telephone system (GPRS, UMTS, HSPA, EVDO, WiMax, 5G etc.), are known as mobile broadband modems (sometimes also called wireless modems). Wireless modems can be embedded inside a laptop, mobile phone or other device, or be connected externally. External wireless modems include connect cards, USB modems, and cellular routers.

Most GSM wireless modems come with an integrated SIM cardholder (i.e. Huawei E220, Sierra 881.) Some models are also provided with a microSD memory slot and/or jack for additional external antenna, (Huawei E1762, Sierra Compass 885.)

The CDMA (EVDO) versions do not typically use R-UIM cards, but use Electronic Serial Number (ESN) instead.

Until the end of April 2011, worldwide shipments of USB modems surpassed embedded 3G and 4G modules by 3:1 because USB modems can be easily discarded. Embedded modems may overtake separate modems as tablet sales grow and the incremental cost of the modems shrinks, so by 2016, the ratio may change to 1:1.

Like mobile phones, mobile broadband modems can be SIM locked to a particular network provider. Unlocking a modem is achieved the same way as unlocking a phone, by using an 'unlock code'.

Optical modem

An ONT providing data, telephone and television service

A device that connects to a fiber optic network is known as an optical network terminal (ONT) or optical network unit (ONU). These are commonly used in fiber to the home installations, installed inside or outside a house to convert the optical medium to a copper Ethernet interface, after which a router or gateway is often installed to perform authentication, routing, NAT, and other typical consumer internet functions, in addition to "triple play" features such as telephony and television service. They are not a modem, although they perform a similar function and are sometimes referred to as a modem.

Fiber optic systems can use quadrature amplitude modulation to maximize throughput. 16QAM uses a 16-point constellation to send four bits per symbol, with speeds on the order of 200 or 400 gigabits per second. 64QAM uses a 64-point constellation to send six bits per symbol, with speeds up to 65 terabits per second. Although this technology has been announced, it may not yet be commonly used.

Home networking

Although the name modem is seldom used, some high-speed home networking applications do use modems, such as powerline ethernet. The G.hn standard for instance, developed by ITU-T, provides a high-speed (up to 1 Gbit/s) local area network using existing home wiring (power lines, phone lines, and coaxial cables). G.hn devices use orthogonal frequency-division multiplexing (OFDM) to modulate a digital signal for transmission over the wire.

As described above, technologies like Wi-Fi and Bluetooth also use modems to communicate over radio at short distances.

Null modem

Null modem adapter

A null modem cable is a specially wired cable connected between the serial ports of two devices, with the transmit and receive lines reversed. It is used to connect two devices directly without a modem. The same software or hardware typically used with modems (such as Procomm or Minicom) could be used with this type of connection.

A null modem adapter is a small device with plugs at both ends which is placed on the termination of a normal "straight-through" serial cable to convert it into a null-modem cable.

Short-haul modem

A "short haul modem" is a device that bridges the gap between leased-line and dial-up modems. Like a leased-line modem, they transmit over "bare" lines with no power or telco switching equipment, but are not intended for the same distances that leased lines can achieve. Ranges up to several miles are possible, but significantly, short-haul modems can be used for medium distances, greater than the maximum length of a basic serial cable but still relatively short, such as within a single building or campus. This allows a serial connection to be extended for perhaps only several hundred to several thousand feet, a case where obtaining an entire telephone or leased line would be overkill.

While some short-haul modems do in fact use modulation, low-end devices (for reasons of cost or power consumption) are simple "line drivers" that increase the level of the digital signal but do not modulate it. These are not technically modems, but the same terminology is used for them.

See also

• 56 kbit/s line
• Handshaking
• Raytheon BBN
• Command and Data modes (modem)
• Fax demodulator
• List of interface bit rates
• List of ITU-T V-series recommendations
• Modulation
• RJ-11
• Time Independent Escape Sequence
• Wake-on-ring

External links

• Hayes-compatible Modems and AT Commands from the Serial Data Communications Programming Wikibook
• International Telecommunication Union ITU: Data communication over the telephone network
• Basic handshakes & modulations – V.22, V.22bis, V.32 and V.34 handshakes
• Getting connected: a history of modems – techradar
• Difference between Modems and Routers – Bugswave
• Telecommunications Transmission_Engineering Volume 2 Facilities - AT&T
• Polish proxies made on 4G modems

Angle Modulation (AnM)

Angle Modulation

Polar Modulation (PoM)

Polar Modulation

Pulse-Amplitude Modulation (PAM)

Principle of PAM: (1) original signal, (2) PAM signal, (a) amplitude of signal, (b) time

Pulse-amplitude modulation (PAM) is a form of signal modulation where the message information is encoded in the amplitude of a series of signal pulses. It is an analog pulse modulation scheme in which the amplitudes of a train of carrier pulses are varied according to the sample value of the message signal. Demodulation is performed by detecting the amplitude level of the carrier at every single period.

Types

There are two types of pulse amplitude modulation:

• In single polarity PAM, a suitable fixed DC bias is added to the signal to ensure that all the pulses are positive.
• In double polarity PAM, the pulses are both positive and negative.

Pulse-amplitude modulation is widely used in modulating signal transmission of digital data, with non-baseband applications having been largely replaced by pulse-code modulation, and, more recently, by pulse-position modulation.

The number of possible pulse amplitudes in analog PAM is theoretically infinite. Digital PAM reduces the number of pulse amplitudes to some power of two. For example, in 4-level PAM there are $2^{2}$ possible discrete pulse amplitudes; in 8-level PAM there are $2^{3}$ possible discrete pulse amplitudes; and in 16-level PAM there are $2^{4}$ possible discrete pulse amplitudes.

Uses

Ethernet

Some versions of the Ethernet communication standard are an example of PAM usage. In particular, 100BASE-T4 and BroadR-Reach Ethernet standard use three-level PAM modulation (PAM-3), while 1000BASE-T Gigabit Ethernet uses five-level PAM-5 modulation and 10GBASE-T 10 Gigabit Ethernet uses a Tomlinson-Harashima precoded (THP) version of pulse-amplitude modulation with 16 discrete levels (PAM-16), encoded in a two-dimensional checkerboard pattern known as DSQ128. 25 Gigabit Ethernet and some copper variants of 100 Gigabit Ethernet and 200 Gigabit Ethernet use PAM-4 modulation.

USB

USB4 Version 2.0 uses PAM-3 signaling for USB4 80 Gbps (USB4 Gen 4×2) and USB4 120 Gbps (USB4 Gen 4 Asymmetric) transmitting 3 bits per 2 clock cycles. Thunderbolt 5 uses the same PHY.

GDDR6X

GDDR6X, developed by Micron and Nvidia and first used in the Nvidia RTX 3080 and 3090 graphics cards, uses PAM-4 signaling to transmit 2 bits per clock cycle without having to resort to higher frequencies or two channels or lanes with associated transmitters and receivers, which may increase power or space consumption and cost. Higher frequencies require higher bandwidth, which is a significant problem beyond 28 GHz when trying to transmit through copper. PAM-4 costs more to implement than earlier NRZ (non return to zero, PAM-2) coding partly because it requires more space in integrated circuits, and is more susceptible to SNR (signal to noise ratio) problems.

GDDR7

GDDR7 will utilize PAM-3 signaling to achieve speeds of 36 Gbps/pin. The higher data transmission rate per cycle compared to NRZ/PAM-2-signaling used by GDDR6 and prior generations improves power efficiency and signal integrity.

PCI Express

PCI Express 6.0 has introduced PAM-4 usage.

Photo biology

The concept is also used for the study of photosynthesis using a specialized instrument that involves a spectrofluorometric measurement of the kinetics of fluorescence rise and decay in the light-harvesting antenna of thylakoid membranes, thus querying various aspects of the state of the photosystems under different environmental conditions. Unlike the traditional dark-adapted chlorophyll fluorescence measurements, pulse amplitude fluorescence devices allow measuring under ambient light conditions, which made measurements significantly more versatile.

Electronic drivers for LED lighting

Pulse-amplitude modulation has also been developed for the control of light-emitting diodes (LEDs), especially for lighting applications. LED drivers based on the PAM technique offer improved energy efficiency over systems based upon other common driver modulation techniques such as pulse-width modulation (PWM) as the forward current passing through an LED is relative to the intensity of the light output and the LED efficiency increases as the forward current is reduced.

Pulse-amplitude modulation LED drivers are able to synchronize pulses across multiple LED channels to enable perfect color matching. Due to the inherent nature of PAM in conjunction with the rapid switching speed of LEDs, it is possible to use LED lighting as a means of wireless data transmission at high speed.

Digital television

The North American Advanced Television Systems Committee standards for digital television uses a form of PAM to broadcast the data that makes up the television signal. This system, known as 8VSB, is based on an eight-level PAM. It uses additional processing to suppress one sideband and thus make more efficient use of limited bandwidth. Using a single 6 MHz channel allocation, as defined in the previous NTSC analog standard, 8VSB is capable of transmitting 32 Mbit/s. After accounting for error-correcting codes and other overhead, the data rate in the signal is 19.39 Mbit/s.

See also

• 8VSB
• Amplitude-shift keying
• Carrier Sense Multiple Access
• Pulse-density modulation
• Pulse forming network
• Quadrature amplitude modulation (QAM)

Pulse-Code Modulation (PCM)

Pulse-Code Modulation

Pulse-Density Modulation (PDM)

Pulse-Density Modulation

Pulse-Width Modulation (PWM)

Pulse-Width Modulation

Delta-Sigma Modulation (ΔΣM)

Delta-Sigma Modulation

Orthogonal Frequency-Division Multiplexing (OFDM)

Orthogonal Frequency-Division Multiplexing

Frequency-Division Multiplexing (FDM)

Frequency-Division Multiplexing

Multiplexing

For multiplexing in electronics and signal processing, see Multiplexer.

Multiple low data rate signals are multiplexed over a single high-data-rate link, then demultiplexed at the other end.

In telecommunications and computer networking, multiplexing (sometimes contracted to muxing) is a method by which multiple analog or digital signals are combined into one signal over a shared medium. The aim is to share a scarce resource – a physical transmission medium. For example, in telecommunications, several telephone calls may be carried using one wire. Multiplexing originated in telegraphy in the 1870s, and is now widely applied in communications. In telephony, George Owen Squier is credited with the development of telephone carrier multiplexing in 1910.

The multiplexed signal is transmitted over a communication channel such as a cable. The multiplexing divides the capacity of the communication channel into several logical channels, one for each message signal or data stream to be transferred. A reverse process, known as demultiplexing, extracts the original channels on the receiver end.

A device that performs the multiplexing is called a multiplexer (MUX), and a device that performs the reverse process is called a demultiplexer (DEMUX or DMX).

Inverse multiplexing (IMUX) has the opposite aim as multiplexing, namely to break one data stream into several streams, transfer them simultaneously over several communication channels, and recreate the original data stream.

In computing, I/O multiplexing can also be used to refer to the concept of processing multiple input/output events from a single event loop, with system calls like poll and select (Unix).

Types

Multiple variable bit rate digital bit streams may be transferred efficiently over a single fixed bandwidth channel by means of statistical multiplexing. This is an asynchronous mode time-domain multiplexing which is a form of time-division multiplexing.

Digital bit streams can be transferred over an analog channel by means of code-division multiplexing techniques such as frequency-hopping spread spectrum (FHSS) and direct-sequence spread spectrum (DSSS).

In wireless communications, multiplexing can also be accomplished through alternating polarization (horizontal/vertical or clockwise/counterclockwise) on each adjacent channel and satellite, or through phased multi-antenna array combined with a multiple-input multiple-output communications (MIMO) scheme.

Space-division multiplexing

Main article: Space-division multiple access

In wired communication, space-division multiplexing, also known as space-division multiple access (SDMA) is the use of separate point-to-point electrical conductors for each transmitted channel. Examples include an analog stereo audio cable, with one pair of wires for the left channel and another for the right channel, and a multi-pair telephone cable, a switched star network such as a telephone access network, a switched Ethernet network, and a mesh network.

In wireless communication, space-division multiplexing is achieved with multiple antenna elements forming a phased array antenna. Examples are multiple-input and multiple-output (MIMO), single-input and multiple-output (SIMO) and multiple-input and single-output (MISO) multiplexing. An IEEE 802.11g wireless router with k antennas makes it in principle possible to communicate with k multiplexed channels, each with a peak bit rate of 54 Mbit/s, thus increasing the total peak bit rate by the factor k. Different antennas would give different multi-path propagation (echo) signatures, making it possible for digital signal processing techniques to separate different signals from each other. These techniques may also be utilized for space diversity (improved robustness to fading) or beamforming (improved selectivity) rather than multiplexing.

Frequency-division multiplexing

Frequency-division multiplexing (FDM): The spectrum of each input signal is shifted to a distinct frequency range.

Frequency-division multiplexing (FDM) is inherently an analog technology. FDM achieves the combining of several signals into one medium by sending signals in several distinct frequency ranges over a single medium. In FDM the signals are electrical signals. One of the most common applications for FDM is traditional radio and television broadcasting from terrestrial, mobile or satellite stations, or cable television. Only one cable reaches a customer's residential area, but the service provider can send multiple television channels or signals simultaneously over that cable to all subscribers without interference. Receivers must tune to the appropriate frequency (channel) to access the desired signal.

One stream, one color, light waves, in WDM

A variant technology, called wavelength-division multiplexing (WDM) is used in optical communications.

Time-division multiplexing

Time-division multiplexing (TDM)

Time-division multiplexing (TDM) is a digital (or in rare cases, analog) technology that uses time, instead of space or frequency, to separate the different data streams. TDM involves sequencing groups of a few bits or bytes from each individual input stream, one after the other, and in such a way that they can be associated with the appropriate receiver. If done sufficiently quickly, the receiving devices will not detect that some of the circuit time was used to serve another logical communication path.

Consider an application requiring four terminals at an airport to reach a central computer. Each terminal communicated at 2400 baud, so rather than acquire four individual circuits to carry such a low-speed transmission, the airline has installed a pair of multiplexers. A pair of 9600 baud modems and one dedicated analog communications circuit from the airport ticket desk back to the airline data center are also installed. Some web proxy servers (e.g. polipo) use TDM in HTTP pipelining of multiple HTTP transactions onto the same TCP/IP connection.

Carrier-sense multiple access and multidrop communication methods are similar to time-division multiplexing in that multiple data streams are separated by time on the same medium, but because the signals have separate origins instead of being combined into a single signal, are best viewed as channel access methods, rather than a form of multiplexing.

TD is a legacy multiplexing technology still providing the backbone of most National fixed-line telephony networks in Europe, providing the 2 Mbit/s voice and signaling ports on narrow-band telephone exchanges such as the DMS100. Each E1 or 2 Mbit/s TDM port provides either 30 or 31 speech timeslots in the case of CCITT7 signaling systems and 30 voice channels for customer-connected Q931, DASS2, DPNSS, V5 and CASS signaling systems.

Polarization-division multiplexing

Polarization-division multiplexing uses the polarization of electromagnetic radiation to separate orthogonal channels. It is in practical use in both radio and optical communications, particularly in 100 Gbit/s per channel fiber optic transmission systems.

Differential Cross-Polarized Wireless Communications is a novel method for polarized antenna transmission utilizing a differential technique.

Orbital angular momentum multiplexing

Orbital angular momentum multiplexing is a relatively new and experimental technique for multiplexing multiple channels of signals carried using electromagnetic radiation over a single path. It can potentially be used in addition to other physical multiplexing methods to greatly expand the transmission capacity of such systems. As of 2012 it is still in its early research phase, with small-scale laboratory demonstrations of bandwidths of up to 2.5 Tbit/s over a single light path. This is a controversial subject in the academic community, with many claiming it is not a new method of multiplexing, but rather a special case of space-division multiplexing.

Code-division multiplexing

Code-division multiplexing (CDM), code-division multiple access (CDMA) or spread spectrum is a class of techniques where several channels simultaneously share the same frequency spectrum, and this spectral bandwidth is much higher than the bit rate or symbol rate. One form is frequency hopping, another is direct sequence spread spectrum. In the latter case, each channel transmits its bits as a coded channel-specific sequence of pulses called chips. Number of chips per bit, or chips per symbol, is the spreading factor. This coded transmission typically is accomplished by transmitting a unique time-dependent series of short pulses, which are placed within chip times within the larger bit time. All channels, each with a different code, can be transmitted on the same fiber or radio channel or other medium, and asynchronously demultiplexed. Advantages over conventional techniques are that variable bandwidth is possible (just as in statistical multiplexing), that the wide bandwidth allows poor signal-to-noise ratio according to Shannon–Hartley theorem, and that multi-path propagation in wireless communication can be combated by rake receivers.

A significant application of CDMA is the Global Positioning System (GPS).

Telecommunication multiplexing

Multiple access method

A multiplexing technique may be further extended into a multiple access method or channel access method, for example, TDM into time-division multiple access (TDMA) and statistical multiplexing into carrier-sense multiple access (CSMA). A multiple-access method makes it possible for several transmitters connected to the same physical medium to share their capacity.

Multiplexing is provided by the physical layer of the OSI model, while multiple access also involves a media access control protocol, which is part of the data link layer.

The Transport layer in the OSI model, as well as TCP/IP model, provides statistical multiplexing of several application layer data flows to/from the same computer.

Code-division multiplexing (CDM) is a technique in which each channel transmits its bits as a coded channel-specific sequence of pulses. This coded transmission is typically accomplished by transmitting a unique time-dependent series of short pulses, which are placed within chip times within the larger bit time. All channels, each with a different code, can be transmitted on the same fiber and asynchronously demultiplexed. Other widely used multiple access techniques are time-division multiple access (TDMA) and frequency-division multiple access (FDMA). Code-division multiplex techniques are used as an access technology, namely code-division multiple access (CDMA), in Universal Mobile Telecommunications System (UMTS) standard for the third-generation (3G) mobile communication identified by the ITU.

Application areas

Telegraphy

The earliest communication technology using electrical wires, and therefore sharing an interest in the economies afforded by multiplexing, was the electric telegraph. Early experiments allowed two separate messages to travel in opposite directions simultaneously, first using an electric battery at both ends, then at only one end.

Émile Baudot developed a time-multiplexing system of multiple Hughes machines in the 1870s. In 1874, the quadruplex telegraph developed by Thomas Edison transmitted two messages in each direction simultaneously, for a total of four messages transiting the same wire at the same time. Several researchers were investigating acoustic telegraphy, a frequency-division multiplexing technique, which led to the invention of the telephone.

Telephony

In telephony, a customer's telephone line now typically ends at the remote concentrator box, where it is multiplexed along with other telephone lines for that neighborhood or other similar area. The multiplexed signal is then carried to the central switching office on significantly fewer wires and for much further distances than a customer's line can practically go. This is likewise also true for digital subscriber lines (DSL).

Fiber in the loop (FITL) is a common method of multiplexing, which uses optical fiber as the backbone. It not only connects POTS phone lines with the rest of the PSTN, but also replaces DSL by connecting directly to Ethernet wired into the home. Asynchronous Transfer Mode is often the communications protocol used.

Cable TV has long carried multiplexed television channels, and late in the 20th century began offering the same services as telephone companies. IPTV also depends on multiplexing.

Video processing

Main article: Demultiplexer (media file)

In video editing and processing systems, multiplexing refers to the process of interleaving audio and video into one coherent data stream.

In digital video, such a transport stream is normally a feature of a container format which may include metadata and other information, such as subtitles. The audio and video streams may have variable bit rate. Software that produces such a transport stream and/or container is commonly called a multiplexer or muxer. A demuxer is software that extracts or otherwise makes available for separate processing the components of such a stream or container.

Digital broadcasting

In digital television systems, several variable bit-rate data streams are multiplexed together to a fixed bit-rate transport stream by means of statistical multiplexing. This makes it possible to transfer several video and audio channels simultaneously over the same frequency channel, together with various services. This may involve several standard-definition television (SDTV) programs (particularly on DVB-T, DVB-S2, ISDB and ATSC-C), or one HDTV, possibly with a single SDTV companion channel over one 6 to 8 MHz-wide TV channel. The device that accomplishes this is called a statistical multiplexer. In several of these systems, the multiplexing results in an MPEG transport stream. The newer DVB standards DVB-S2 and DVB-T2 has the capacity to carry several HDTV channels in one multiplex.

In digital radio, a multiplex (also known as an ensemble) is a number of radio stations that are grouped together. A multiplex is a stream of digital information that includes audio and other data.

On communications satellites which carry broadcast television networks and radio networks, this is known as multiple channel per carrier or MCPC. Where multiplexing is not practical (such as where there are different sources using a single transponder), single channel per carrier mode is used.

Analog broadcasting

In FM broadcasting and other analog radio media, multiplexing is a term commonly given to the process of adding subcarriers to the audio signal before it enters the transmitter, where modulation occurs. (In fact, the stereo multiplex signal can be generated using time-division multiplexing, by switching between the two (left channel and right channel) input signals at an ultrasonic rate (the subcarrier), and then filtering out the higher harmonics.) Multiplexing in this sense is sometimes known as MPX, which in turn is also an old term for stereophonic FM, seen on stereo systems since the 1960s.

Other meanings

In spectroscopy the term is used to indicate that the experiment is performed with a mixture of frequencies at once and their respective response unraveled afterward using the Fourier transform principle.

In computer programming, it may refer to using a single in-memory resource (such as a file handle) to handle multiple external resources (such as on-disk files).

Some electrical multiplexing techniques do not require a physical "multiplexer" device, they refer to a "keyboard matrix" or "Charlieplexing" design style:

• Multiplexing may refer to the design of a multiplexed display (non-multiplexed displays are immune to break up).
• Multiplexing may refer to the design of a "switch matrix" (non-multiplexed buttons are immune to "phantom keys" and also immune to "phantom key blocking").

In high-throughput DNA sequencing, the term is used to indicate that some artificial sequences (often called barcodes or indexes) have been added to link given sequence reads to a given sample, and thus allow for the sequencing of multiple samples in the same reaction.

In sociolinguistics, multiplexity is used to describe the number of distinct connections between individuals who are part of a social network. A multiplex network is one in which members share a number of ties stemming from more than one social context, such as workmates, neighbors, or relatives.

See also

• Add-drop multiplexer
• Channel bank
• Multiplexed display
• Optical add-drop multiplexer
• Orthogonal frequency-division multiplexing (OFDM) (which is a modulation method)
• Statistical multiplexing

References

• "Federal Standard 1037C: Glossary of Telecommunications Terms". Institute for Telecommunication Services. Archived from the original on 2009-03-02. Retrieved 2009-10-19.
• Efficient beam multiplexing using a spatial light modulator

External links

• The dictionary definition of multiplexing at Wiktionary
• Media related to Rai282/Books/Modulation at Wikimedia Commons